Document ID:06080001
Rev: L
Technical Support: 800-626-6912
Page 13 of 24
S
PECIFICATIONS
Hot and cold water supply lines required
(hot and cold shut offs may be installed under pedicure spa
base) See pages seven through ten.
Drain installation:
references noted on pages seven through ten, can be installed with optional
power drain pump or as gravity drain.
Overall dimensions without accessories, seat upright:
54" (138cm) L x 31" (79cm) W x 56" (143cm) H*
Without accessories, seat collapsed:
(shipping position): 54" (138cm) L x 32" (82cm) W x 36" (92cm) H*
Shipping dimensions:
55" (140cm) L x 33" (84cm) W x 41" (105cm) H*
Empty weight:
150 Ibs (68kg)*
Shipping weight:
205 lbs (93kg)*
Capacity of basin:
5 U.S. Gallons (18.9L) = Traditional Whirlpool
(with Jets)
*
6.5 U.S. Gallons (25.6L) = Crystal Clean
™
Pipe-Free
®
*
Whirlpool pump motor: 110V:
1/6 HP, 110V, 60HZ (alternate voltages available) (3/4 HP for Traditional
Whirlpool -
with Jets
)
220V:
1/6 HP, 110V, 50Hz (alternate voltages available) (3/4 HP for Traditional
Whirlpool -
with Jets
)
Forte seat and back motors:
30V DC Linear Actuators. Forte requires 18” (46 cm) of space between
pedicure spa and wall with standard actuator.*
Altera seat and back movement:
2 infinitely adjustable lockable gas cylinders for reclining/sliding. The
Altera requires 12" (31cm) of space between pedicure spa and wall in order for
seat to recline to its fullest extent.*
Massage motor:
12V AC, Adapter included (alternate voltages available)
Power source:
110V:
110V AC / 15 Amp, 60 Hz (GFCI Protected)
220V:
220-240VAC, 50Hz, 7.5 Amp (GFCI Protected)
Caution: Pedicure spa must be installed by a licensed electrician and a licensed plumber,
conforming to all local and national electrical codes.
Construction:
Linear Low Density Polyethylene (LLDPE), self-contained, pre-plumbed
Crystal Clean
™
Pipe-Free
®
water massage system (pipe-free
pedicure spas):
'underfoot' footplate
water massage grooves, no closed loop circulating pipes, 100% fully drained,
and cleanable
Hydro-Therapeutic (Jet System: Traditional Whirlpool pedicure spas):
PVC, two (2) fully-directional
jets, built-in air control
Electrical switches:
On/Off switch for whirlpool pump. Hand-held low voltage remote controls for
massage motors, heat, and seat/back position. Hot and Cold water supply lines
required.
UL listed/CE certified:
Complies with ASME/ANSI Whirlpool Bathtub Specs ASME/ANSI A112.19 7M-
1995 and A112.19.8M-1995. Backflow Protection Devices for Faucets with Side
Spray: Check valves comply with ANSI/ASME A112.18.3M, A112.18.1M, and
CSA B125.
Performance Limits:
1. This unit may loose one ore more functions when electrostatic contact
discharge in excess of 4KV gets into accessible conductive part of the unit and
can be restored by resetting the unit.
2. This unit may loose one ore more functions when power surge in excess of
2KV is applied to the AC input power port and can be restored by resetting the
unit.
3. This unit may loose one ore more functions when subjected to fast transient
voltages in excess of 0.5KV at 5 KHz repetition frequency and can not be
restored.
Limited warranty:
One (1) year from date of purchase.
Due to our policy of continuous improvements, all specifications are subject to change without notice.
*Note: All dimensions and weights are approximate
