European Home H Series страница 21 Скачать руководство пользователя

Страница: 21 / 36

TRIM and FINISH

H Series

Vent Free Fireplace Rev #12042020 European

Home

.com

FINISHING THE ENCLOSURE

The

H Series

Vent Free Gas Fireplace is designed to be enclosed with common building materials; wood,

drywall, plaster, etc.

•

Any combustible mantels must be installed within the limits.

•

Provided the required clearances are maintained, the walls that enclose the sides of the fireplace may

be constructed of combustible material.

The facing within the limits must be made of non-combustible

material.

•

The facing flanges on these fireplaces are designed for use with 1/2” thick facing. Non-combustible facing

must be used as shown previously.

•

The wall above the fireplace opening is constantly exposed to elevated temperatures. This must be

considered when choosing any fasteners, paint, mastic, sealant, caulk, etc. for use in this area as materials

may change color or emit an odor when heated. Petroleum-based tile adhesives should be avoided and

thin-set mortar used instead.

The fire media must be installed per these instructions. This heater must use only the fire media provided

by European Home. An excess amount of fire media may adversely affect the performance of the heater.

WARNING: All previously applied loose material must be removed prior to reapplication.

INSTALLING THE FIRE MEDIA

Two types of fire media are available for your

H Series

Vent Free Gas Fireplace; Fireglass or Carrara Pebbles.

The Fire Media

The entire contents of the bag of fire media should be spread to an even depth across the entire burner top.

Be certain that media does not come within 1/4” of the pilot burner. Media dust should not be emptied on burner

top as it may clog the gas parts.

Содержание H Series





































Результаты поиска

Содержание H Series

Отзывы:

Похожие инструкции для H Series

Бренды по названию

Популярные бренды

European Home H Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание H Series

Отзывы:

Похожие инструкции для H Series

Бренды по названию

Популярные бренды