European Home H Series страница 19 Скачать руководство пользователя

Страница: 19 / 36

GAS INSTALLATION

H Series

Vent Free Fireplace Rev #12042020 European

Home

.com

The installation of this fireplace must conform with local codes or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1.

The

H Series Vent Free Gas Fireplace

is shipped from the factory for use with natural gas

ONLY

Conversion to another fuel is

NOT

permitted.

This product must be installed by a licensed plumber or gasfitter when installed within the

Commonwealth of Massachusetts.

Note

Gas Supply Opening On Either Side (see text)

9”

33/16”

Fireplace

Opening

Cabinet

Bottom

Building codes do not permit the installation of

a gas fireplace in a plenum (a chase designed for

air flow) but your enclosure may have local air

movement within it. To limit the movement of air

on the pilot and/or burner flames the knockout

opening(s) should be sealed with aluminum (non-

combustible) duct tape.

INSTALL THE GAS SUPPLY

A 51/8” x 31/2” knockout opening in the lower left and right sides is provided for the gas supply. The dimensions

to the center of this opening are shown below.

NOTE:

The knockout must be sealed off after being taken

off to prevent air from the walls shutting off the pilot light.

If the gas and electrical lines cannot be run to the provided knockouts, a seperate hole may be drilled to bring

gas and electrical into the unit. This hole must be located below the hearth tray and sealed completely after

the gas and electrical lines have been brought into the unit.

The gas supply piping should have a separate gas shutoff valve and a capped,

1/8

” pipe tapping upstream of the

valve for the purpose of reading pressure. A service shutoff valve must be placed within six feet of the fireplace

gas control valve.

The gas supply line must terminate with a

1/2

” male flare fitting. The gas supply pressure at the gas control valve

must not exceed 7.0” w.c. (1.7 kPa)

The appliance and its appliance main gas valve must be

disconnected

from the gas supply piping system during

any pressure testing of that system at test pressures in excess of

1/2

psi (3.5 kPa). The appliance must be

isolated

from the gas supply piping system by closing its equipment shutoff valve during any pressure testing of the

Содержание H Series





































Результаты поиска

Содержание H Series

Отзывы:

Похожие инструкции для H Series

Бренды по названию

Популярные бренды

European Home H Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание H Series

Отзывы:

Похожие инструкции для H Series

Бренды по названию

Популярные бренды