manualshive.com logo in svg

Euroheat FB50, Установка и обслуживание

Поделиться
Скачать
Euroheat FB50 Скачать руководство пользователя страница 32

©

 

EUROHEAT

 

DISTRIBUTORS (H.B.S) LTD. Dec 2004

E & OE     Instructions Part number IN1084 Ed D

32

Commissioning

a) 

Carry out a gas leak test as regulations require.

b) 

Ensure that all openable doors and windows in the room are shut, light the stove and operate 

on  maximum  for  five  minutes.  Position  a  smoke  match  just  beside  the  thermocouple  TTB  (see 

diagram) and check that all the smoke is drawn into the opening to the flue diverter.

IF SPILLAGE IS STILL OBSERVED, THERE MAY BE A PROBLEM WITH THE FLUE SYSTEM OR 

CHIMNEY, DISCONNECT THE APPLIANCE  UNTIL THE PROBLEM HAS BEEN IDENTIFIED.

Note: 

If there are any extractor fans in the room or adjacent rooms, these must be running at maximum 

setting with all interconnecting doors left open, and the spillage test repeated.

c)  

Carry  out  a  gas  operating  pressure  test. Attach  a  manometer  to  the  operating  pressure 

test nipple. With the appliance operating at maximum, observe the operating pressure. Adjust if 

required.

d) 

Carry out a low burn operating pressure test. Attach a manometer to the operating pressure 

test  nipple. Turn  the  gas  valve  control  knob  to  the  minimum  flame  size.  Observe  the  operating 

pressure.

e) 

Carry out a gas supply pressure test with the appliance operating. Attach a manometer to the 

supply pressure test nipple. If the pressure is below requirements inspect gas pipe installation for 

possible problems.

Содержание FB50



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды