background image

6

TECHNICAL INFORMATION FOR

INSTALLATION PERSONNEL

This appliance shall be installed only by authorised

persons and in accordance with the manufacturer's

installation instructions, local gas fitting regulations,

municipal  building  codes,  electrical  wiring

regulations, AS 5601/AG 601 - Gas Installations and

any other statutory regulations.

The wall and bench surfaces must be capable of

sustaining temperatures of 75 degrees Celsius.

All laminates, fixing adhesive and surfacing materials

should be certified suitable for this temperature.

Any adjoining wall surface situated within 200 mm from

the edge of any hob burner must be a suitable non-

combustible material for a height of 150 mm for the entire

length of the hob. Any combustible construction above the

hotplate must be at least 650 mm above the top of the

burner and no construction shall be within 450 mm above

the top of the burner. A minimum depth of 60 mm from the

top of the worktop surface must be provided for the

appliance.

3) INSTALLING THE HOT PLATE

Check that the appliance is in a good condition after

having removed the outer packaging and internal

wrappings from around the various loose parts. In

case of doubt, do not use the appliance and contact

qualified personnel.

Never leave the packaging materials (cardboard,

bags, polystyrene foam, nails, etc.) within

children’s reach since they could become

potential sources of danger.

The measurements of the opening made in the top

of the modular cabinet and into which the hot plate

will be installed are indicated in fig. 7.

Always comply with the measurements given for the

hole into wich the appliance will be recessed (see

fig. 7).

The  appliance  belongs  to  class  3  and  is

therefore  subject  to  all  the  provisions

established by the provisions governing such

appliances. 

INSTALLATION

FIG. 7

COMPLY WITH THE DIMENSIONS (mm)

A

B

C

D

E

4F- 5F (860)

833

475

62.5

62.5 73.5 min.

IMPORTANT: 

a  perfect  installation,  adjustment  or

transformation of the cook top to use other

gases requires a QUALIFIED INSTALLER: a

failure  to  follow  this  rule  will  void  the

warranty.

Содержание EGZ900WWFSX

















Отзывы: