EUCHNER CES-A-ABA-01 Скачать руководство пользователя страница 10

Страница: 10 / 40

Operating Instructions
Non-Contact Safety System CES-A-ABA-01/CES-A-ABA-01B

(translation of the original operating instructions) 071873-15-07/15

7. Mounting

NOTICE

Device damage due to improper installation or unsuitable ambient conditions.

Read heads and actuators must not be used as a mechanical end stop.

Observe EN ISO 14119:2013, sections 5.2 and 5.3, for information about fastening the safety

switch and the actuator.

Observe EN ISO 14119:2013, section 7, for information about reducing the possibilities for by-

passing an interlocking device.

The evaluation unit must be mounted in a control cabinet with a minimum degree of protection of

IP54. A snap-in element on the rear of the device is used for fastening to a mounting rail.

If several evaluation units are mounted side by side in a control cabinet without air circulation

(e.g. fan), a minimum distance of 10 mm must be maintained between the evaluation units. This

distance enables the heat from the evaluation unit to dissipate.

Important!

From the assured switch-off distance S

, the safety outputs are safely shut down.

When mounting several read heads, observe the stipulated minimum distance to avoid mutual in-

terference.

-For CES-A-LNA/-LCA s

min

= 50 mm

-For CES-A-LMN

min

= 20 mm

-For CES-A-LQA

min

= 80 mm

min

If the actuator is installed flush, the switching distance changes as a function of the installation

depth and the safety guard material.

Operating

distance

Actuator

Operating

distance

Actuator

Flush mounting

Surface mounting

Note the following points:

Actuator and read head must be fitted so that

-the front faces are at the minimum switch-on distance 0.8 x S

or closer when the safety guard is closed (see section

Operating distances). To avoid entering the area of possible side lobes, a minimum distance is to be maintained in

case of a side approach direction. See section Typical operating distance for the related actuator.

-a hazard is excluded until the assured switch-off distance (S

) is reached when the safety guard is open.

-the actuator is positively mounted on the safety guard, e.g. by using the safety screws included.

-they cannot be removed or tampered with using simple means.

Pay attention to the maximum tightening torque for the read head or safety switch and actuator mountings of 1 Nm. For

read heads/actuators made of PE-HD, the maximum tightening torque is only 0.5 Nm.

Содержание CES-A-ABA-01









































Результаты поиска

Содержание CES-A-ABA-01

Отзывы:

EUCHNER CES-A-ABA-01, Руководство по эксплуатации, Страница: 10 / 40

Результаты поиска

Содержание CES-A-ABA-01

Отзывы: