EUCHNER 156233 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

EUCHNER 156233 Скачать руководство пользователя страница 26

Operating Instructions

Non-Contact Safety Switch CES-I-BR-.-C07-…

26

(translation of the original operating instructions) 2510145-05-08/21

14.4. Acknowledging error messages

If the DIA LED flashes inversely once, the error message can be acknowledged by opening and closing the guard. If the

error is still displayed afterward, a reset must be performed.
If the LED DIA is permanently illuminated, the error message can be acknowledged only by a reset.
The reset can be performed as follows.

Reset

Centrally for all

switches of a

chain

Each switch

must be

addressed

separately

Further information

By briefly disconnecting the power supply

-

-

Via the cyclical data of IO-Link communication

-

See operating instructions for the IO-Link Gateway

Via the acyclical data of IO-Link communication

-

11.3.2. Acyclical data (device data and events) on page

Resetting to acknowledge error messages does not delete the parametrization.

Important!

Contact the manufacturer if the fault display is not reset after briefly disconnecting the power supply.

«
...
24
25
26
27
28
...
»

Содержание 156233









































Отзывы:

Нет отзывов