background image

Technical instructions

for Installation

4

DESHU - October 2015

A. 

Receipt

Each unit is checked and tested at the factory, prior to shipment, and a test certifi cate is issued. Unless 
otherwise requested in the project specifi cations, units are delivered fully assembled and charged with 
pressurised refrigerant.
Unless otherwise specifi ed, units are delivered without packaging. 

1. 

At arrival on site, 

check the unit for transport damage

.

2. 

If you detect or suspect any damage, please note any necessary reservations on the transport document. 
Confi rm your reservations in a registered letter within 24 hours and inform your sales contact person.

3. 

Remove the adhesive tape

 used to prevent doors from opening during transport.

4.  

If necessary, you will fi nd your 

access key

 fi xed to the technical section ventilation grid or to the handle. A 

spare key is also fi xed to the document holder, next to the electrical board.

5. 

Make sure that all unassembled components are included (refer to the check list of accessories).

6. 

For handling and assembling instructions, refer to the 

installation instructions

 located in the document 

holder, next to the electrical cabinet.

B. 

Handling

Use the supplied lifting lugs

 to lift and transport the unit using a forklift or a crane.

When using a crane, use slings or 

nylon webbing and shackles

 to handle the unit. Extend with chain slings if 

necessary.
If you use short slings, always use a lifting beam to avoid damaging the roof or scratching the casing.
Lifting loads: for more information about weight distribution, please contact the project coordinator at the 
following email address: 

[email protected]

1/ 

General information

1.1/  Installing a packaged unit

•  Handling with a crane

Units are equipped with lifting lugs on casing (on the lower 
part).
Slings minimum length must be twice the unit width plus the 
unit height (see example below).
Slowly pull the chains or slings taut until the unit starts moving.
Take the unit to the installation area.

Example: L = A + B = (2 x 2.4) + 2 = 6.8 m minimum

A

A

2.40 m

2 m

B

Содержание DESHU SM/HPE+


















Отзывы: