manualshive.com logo in svg

ETS 5506-00, Руководство по эксплуатации

Операционный мануал ETS 5506-00 доступен для бесплатного скачивания на {вебсайте}. Пользователи могут легко найти и загрузить руководство по эксплуатации для данного продукта. Этот мануал содержит все необходимые инструкции для правильной настройки и использования изделия. Необходимая информация всегда под рукой!

Поделиться
Скачать
background image

 

 

17

3.2.3 Installation

 

 

3.2.3.1 Initial Check Out  

 

Unpack the Control Unit and Sensor and inspect for visible 
damage. If no damage is observed then proceed to check 
out the system as follows:  

 

 

1.  The Humidity Sensor is already connected to the Control 

Unit when shipped. 

 

2.  Connect the line cord into the appropriate power outlet 

(MAINS). Be sure the POWER switch is in the OFF 
position and the DEHUMIDIFIER switch is in the OFF 
(out) position. Plug the Dehumidification System into the 
AC outlet. 

 

NOTE:

 

All ETS operating systems utilize the standard 3-prong 
North American plug. A 230V/50Hz system will be 
marked as 230V, but will still have the same 3-prong 
plug

. 

 

3.  Turn on the Controller (the POWER switch is located on 

the rear panel). The LCD readout will initially read a 
humidity level much lower than ambient and the Green 
DEHUMIDIFIER indicator should be OFF.  

 

4. The LCD reading will slowly start to increase until it 

reaches the ambient RH level. This may take as long as 
5 minutes if the ambient humidity is very high. 

 

5.  Depress the READ RH/SET RH Switch to the SET PT 

position. The Display will read some level. While holding 
the switch down in the SET PT position, rotate the 
ADJUST Control to the desired RH level set point using a 
small (1/8”/3mm) screwdriver.  

 

6.  Release the switch so that it returns to the READ RH 

(out) position and note the humidity level reading on the 
display. Turn on the DEHUMIDIFIER switch (Green 
button out). If the set point is below ambient, the Green 
DEHUMIDIFIER ON light will turn on and power will be 
applied to the Dehumidifier outlet, activating the 
dehumidification system. If the SET PT is above the 
ambient RH reading, the Green LED indicator light will be 
off. 

 

 

7. The  dehumidification  process will start. The 

Dehumidification System will remain on until the set point 

Содержание 5506-00





























Отзывы:

Нет отзывов

Похожие инструкции для 5506-00

Бренды по названию

Популярные бренды

Загрузить еще бренды