ETS-Lindgren EMCenter Скачать руководство пользователя | Manualshive

Страница: 26 / 43

background image

26

Manual Control of the EMCenter

www.ets-lindgren.com

Powering On and Off

P

OWER

O

N

Verify all cards are installed correctly in the EMCenter.

1.

Plug the power cord from the mains inlet on the back panel of the
EMCenter into a power outlet.

2.

Plug the interlock jack into the interlock connector on the back panel of
the EMCenter.

3.

Turn the power switch located on the back panel of the EMCenter to
the on position.

4.

Touch anywhere on the EMCenter screen. It will take approximately
20 seconds to boot. The Information screen will flash, and then the
Home screen will display.

Sample EMCenter Home Screen

«
...
24
25
26
27
28
...
»

Содержание EMCenter












































Отзывы:

Нет отзывов

Похожие инструкции для EMCenter

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Stage Piano MP8

Бренд: Kawai Страницы: 70

Бренд: WAGNER Страницы: 9

Бренд: BizLine Страницы: 62

Бренд: Kane Страницы: 35

Бренд: Veris Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды