ETS-Lindgren 4310 Скачать руководство пользователя страница 33

Страница: 33 / 36

MODEL 4310 CCTV

Charging the Shielded Battery Pack

REV A – PN 399280

CHARGING THE SHIELDED BATTERY
PACK

If a shielded battery pack is used to power the interface PCB and the

camera inside the camera assembly the pack will need to be charged

after about 12 hours use. Heavy use of the pan and tilt functions will

reduce the battery life.

Proceed as follows:

1. Connect the charger to a suitable mains supply (110 or 240 V ac)

outside

the screened room.

2. Connect the special charging connectors (Red and Black) to the

charger and check that the selector knob is set to 12V.

3. Disconnect the battery pack from the camera assembly and remove

the pack from the test chamber.

4. Connect the battery pack to the charger via the charging lead.

5. Switch On the main supply. Check that the red light on the charger is

lit.

6. Continue charging until the Green light is lit to indicate a full charge.

NOTE:

Do not re-connect the battery to the camera assembly until it

is required for use, as the camera and the PCB in the camera

assembly are on when the cable is connected.

Содержание 4310





































Результаты поиска

Содержание 4310

Отзывы:

Похожие инструкции для 4310

Бренды по названию

Популярные бренды

ETS-Lindgren 4310, Руководство пользователя

Результаты поиска

Содержание 4310

Отзывы:

Похожие инструкции для 4310

Бренды по названию

Популярные бренды