background image

Page 10 of 16 

 

ETM9900(J) Quick Start Guide Issue 27012009 

Modem Initialisation Settings - Main Init Tab 

Modem AT Initialisation settings can be sent to the modem using the Main Init Tab. 

 

AT^SCFG

=“Radio/Band”,”X” (where X=band)  

 X=1, 

GSM 

900MHz 

 X=2, 

GSM 

1800MHz 

 

X=16, WCDMA 2100MHz 

 

X=64, WCDMA 850MHz (NextG™) 

 

X=65, GSM 900MHz & WCDMA 850MHz 

 

X=80, WCDMA 850/2100MHz  

            X=127, Default setting all bands 

ATS0=2

 Will set the unit to answer an incoming call after 2 rings, and may be useful for 

applications using a Circuit Switch Data Call. 

Control Via ET Commands 

As default the ETM9900(J) is set to ET Command Mode, ET Commands are specific to ETM 
terminals and allow for control, configuration and information requests to be sent to and from the 
terminal. In ETM command mode AT commands cannot be sent to the unit. 
ET commands can be sent via SMS or from configuration tool when directly connected or via an IP 
or CSD connection. It is recommended that more complex settings such as changing messages or 
phone numbers are made using the configuration tool. 
Common ET commands are shown below, for a full ET command list download the relevant 
documents from Docbanq (see page 3). 
 

 

Содержание ETM9900(J)

















Отзывы: