Eteros Mobius Скачать руководство пользователя

Страница: 10 / 17

MOBIUS TUMBLER AND BRUSH WASHER USER GUIDE

OPERATIONAL PREP

CONTROL PANEL OVERVIEW

COMPONENT INSTALLATION AND

REMOVAL

Please take the following steps to confirm the MTB Washer is ready to operate:

• Complete a thorough inspection of the equipment to ensure there is no damage and that all

components are in place.

•

Confirm the power cord is in good condition.

• Ensure the lid is properly installed with the limit switch pin in place

• Ensure that the equipment is in a clear and tidy workspace and that all controls are accessible

• Connect the drainage hose to the drainage outlet on the MTB Washer basin and ensure that

the valve on the outlet is closed.

E-STOP

- Prevents accidental start-up, used for

servicing and removing components.

START

–Starts motor rotation

STOP

– Stops motor rotation

LIGHT

- Green when powered on (running)

Remove the spreader

assembly from the washer

and place the drive (left)

end on the ground

START

STOP

E-STOP

INDICATOR LIGHT

Содержание Mobius


















Результаты поиска

Содержание Mobius

Отзывы:

Похожие инструкции для Mobius

Бренды по названию

Популярные бренды

Eteros Mobius, Руководство пользователя

Результаты поиска

Содержание Mobius

Отзывы:

Похожие инструкции для Mobius

Бренды по названию

Популярные бренды