ETC Source Four XT HID Zoom 15-30 Скачать руководство пользователя страница 3

Страница: 3 / 20

Basic Assembly

Figure-1 Components of the Source Four HID Zoom Fixture.

Basic Information

ETC’s Source Four XT HID Zoom is a Source Four spotlight for all-weather use. Powerful Source

Four optics, light output and energy savings in a sleek IP66-rated watertight and dustproof design.

XT features ETC’s Source Four Zoom 15° to 30° optical system plus our longlife 12,000-hour, 150W

HID lamp. Hang by yoke, place on ground, attach to poles and other structures.

Applications

W A R N I N G :

Please note the following safety warnings before use:
Do not use this fixture with a damaged power lead. If the power lead

(cordset) is damaged, it must be replaced.
Do not mount the fixture on or near combustible surfaces.
Do not use this fixture if glass lens is deeply scratched or cracked. Damaged

lenses must be replaced.
Do not operate the fixture for long periods of time without the barrel

installed.
Remove foam packing from internal lenses before connecting power to your

fixture.

•

Houses of worship

•

Retail store logos and patterns

•

Theme parks

•

Outdoor performance venues (non-dimming)

•

Museums

•

Public sculptures

•

Outdoor signage

Reflector

housing

Ballast

Pattern holder

Barrel

Yoke

Barrel locating

hole

Focus lens

and frame

Field lens

and frame

Pattern holder

slots

Locating pin

Содержание Source Four XT HID Zoom 15-30





















Результаты поиска

Содержание Source Four XT HID Zoom 15-30

Отзывы:

Похожие инструкции для Source Four XT HID Zoom 15-30

Бренды по названию

Популярные бренды

ETC Source Four XT HID Zoom 15-30, Руководство пользователя

Результаты поиска

Содержание Source Four XT HID Zoom 15-30

Отзывы:

Похожие инструкции для Source Four XT HID Zoom 15-30

Бренды по названию

Популярные бренды