ETC ArcSystem Pro D4 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 68

ETC ArcSystem Pro D4 Series Скачать руководство пользователя страница 40

34

D4 Series Drivers Installation Guide

Wall-Mount Emergency Driver Installation

CAUTION:

RISK OF SHOCK AND FIRE - This unit has more than one power

supply connection point. To reduce the risk of electric shock disconnect both
the branch circuit-breakers or fuses and emergency power supplies before
servicing.

ATTENTION :

RISQUE D'INCENDIE ET DE CHOC - Cet appareil posséde

plusieurs points de connexion d'alimentation. Pour réduire le risque de choc
électrique déconnecter les disjoncteurs de dérivation ou les fusibles et les
alimentations de secours avantl'entretien.

CAUTION:

Service by qualified personnel only. De-energize before opening.

ATTENTION :

Service par du personnel qualifié uniquttes. Hors tension

avant d'ouvrir.

With the exception of power input terminations, Wall-Mount D4 Emergency Driver installation
requirements are the same as those of the standard Wall-Mount D4 Driver. Complete the
installation as follows, referencing these sections for installation details:

•

Review

Prepare for Wall-Mount Installation on page 17

•

Review

Electrical and Wiring Specification on page 15

•

Complete

Wall-Mount the Driver on page 17

•

Complete

Terminate Normal Sense Input on the facing page

•

Complete

Terminate Maintained (Emergency) Input on page 36

•

Complete

Output Wiring on page 22

•

Complete

DMX In and DMX Thru on page 23

After completing D4 Emergency Driver installation, see

Final Installation and Operation on

Note:

Normal and emergency wiring cannot be contained in the same conduit

according to NEC 700.10(B).

Note:

Use suitable conduit where required by local or national code.

«
...
38
39
40
41
42
...
»

Содержание ArcSystem Pro D4 Series





































































Отзывы:

Нет отзывов