manualshive.com logo in svg

ETC ArcSystem Pro D4 Series, Руководство по установке, Страница: 18 / 68

Поделиться
Скачать
ETC ArcSystem Pro D4 Series Скачать руководство пользователя страница 18

12

D4 Series Drivers Installation Guide

One-Cell Luminaire Installation

This chapter provides information on how to install ArcSystem Pro One-Cell luminaires in a
standard ArcSystem installation.

Preparing the Ceiling for Recessed Luminaires

This section is specific to the recessed/flush mounted variant of luminaires. For Pro One-Cell
yoke-mounted luminaires, proceed to

Installing One-Cell Yoke-Mounted Luminaires on page 14

.

Cut a hole in the ceiling or ceiling tile to accommodate the luminaire’s retaining clip anchors.
Cut the hole larger than the minimum hole diameter listed below and smaller than the
luminaire’s outer bezel. The images below provide an example of the bezels on the Pro One-
Cell luminaires.

Luminaire

Minimum Hole Diameter

Pro One-Cell

16.5 cm (6-1/2 in)

Pro One-Cell High Output

17.0 cm (6-11/16 in)

Pro One-Cell Small

9.5 cm (3-3/4 in)

Pro One-Cell Micro

7.6 cm (3 in)

Note:

If you are installing the luminaire into an ArcSystem Recessed Ceiling Adapter,

refer to the

ArcSystem Recessed Ceiling Adapter Installation Guide

for the minimum

diameter hole to cut in the ceiling to clear the flange on the bottom of the bracket.

Note:

Maximum ceiling thickness for safe use of the luminaire retaining clips is

1.9 cm (¾ in).

Содержание ArcSystem Pro D4 Series





































































Отзывы:

Нет отзывов