background image

 

17 

 
 
 

WARRANTY: 

All goods manufactured by G&C Electronics cc T/A ET Systems carry a 12 month factory warranty from date 

of invoice. All goods are warranted to be free of faulty components and manufacturing defects. Faulty goods will be 

repaired or replaced at the sole discretion of ET Systems free of charge. This warranty is subject to the goods being 

returned to the premises of ET Systems. The carriage of goods is for the customers account. This warranty is only valid if the 

correct installation and application of goods, as laid out in the applicable documentation accompanying said goods, is 

adhered to. All warranty claims must be accompanied by the original invoice. All claims made by the end user must be 

directed to their respective service provider/installer.  

 

The following items are not included in the warranty. 

 

The light globe 

 

The batteries 

 

Motor brush wear 

 

Acceptable wear and tear. 

 

The following conditions will disqualify this product from the warranty as laid out above. 

These conditions are non-negotiable. 

 

Any single ET BLUE ROLL garage door operator used to automate more than one door at one time.

 

 

Any ET BLUE ROLL garage door operator used outdoors, including carports or non weatherproof 

environments.

 

 

Any ET BLUE ROLL domestic garage door operator used in excessive traffic applications for example an 

apartment-block parking garage.

 

 

Any unauthorised non-manufacturer modifications to the product or components thereof. 

 

 

Содержание BLUE-ROLL


















Отзывы: