background image

                          

         

  

 

10 

 

ET-P672275 

43.78 

36.72 

600 

7.49 

7.96 

275 

ET-P672280 

43.78 

36.72 

600 

7.63 

7.98 

280 

 

ET-P660200 

36 

28.75 

600 

7.7 

7.71 

200 

15 

ET-P660205

 

36 

28.75 

600 

7.13 

7.8 

205 

ET-P660210 

36 

28.75 

600 

7.3 

7.99 

210 

ET-P660215 

36 

29 

600 

7.41 

8.1 

215 

ET-P660220 

36.3 

29 

600 

7.58 

8.1 

220 

ET-P660225 

36.3 

29 

600 

7.75 

8.1 

225 

ET-P660230 

36.5 

29.4 

600 

7.82 

8.3 

230 

ET-P660235 

36.5 

29.4 

600 

7.99 

8.3 

235 

 

Usually the load of the modules is a group of batteries. To prevent the modules from 

being charged by batteries under the circumstance of no sunlight, it is important to add a 

shut-off diode in series. Also, please consider the voltage decrease of PN junction of 

about 0.7V when connecting the shut-off diode. The modules can withstand for a 

maximum positive or negative design loading of 45 lbs / ft

2

.

 

 

The  environmental temperature  may also affect the modules’ output power.  If the 

environmental  temperature goes up, the short-circuit current will increase a little,  while 

open-circuit voltage will decrease, which will result in a decrease in the module’s output 

power. Therefore, a lower environmental temperature is most appropriate for the module. 

 

5. Operation and Maintenance  

ET Solar module users should rinse the array seasonally or as needed in dry, dirty areas 

to improve the performance of their solar electrical systems. Heavily soiled modules will 

have a decrease in performance due to reduced light on the photovoltaic cells. Studies by 

the PVUSA in Davis, CA estimate that during a dry year module soiling may affect 

performance by as much as 7% annually with no cleaning. Seasonal rains often clean the 

modules, however, during the long dry summer, it is helpful to rinse the modules as 

needed. 

ET solar modules may be rinsed with clean water to remove dirt. Normal pressure from a 

standard residential hose and nozzle is recommended. Early morning and late afternoons 

are favorable times to clean to avoid a sudden change in temperature. Care must be taken 

since modules produce energy any time light is present. Modules are not to be touched or 

walked on except by a licensed professional. 

 

Содержание ET-P654180













Отзывы: