background image

 

 

 

ES-220 RACK CONVEYOR DISHWASHER – JUNE 2011 

I

MPORTANT

:

 PRIOR TO INSTALLATION

 

1.1

 

 

Installation must be carried out according to local regulations by 
qualified trade persons.  Isolating switch(es), shut-off valves etc must 
be within easy reach of the machine for future service and 
maintenance requirements. If in doubt call ESWOOD AUSTRALIA or 
their representative for further information. No responsibility will be 
accepted for defects or damages by improper installation, for 
changes to the product not authorised by ESWOOD AUSTRALIA, or 
for operation outside the technical specifications. 
 
ESWOOD AUSTRALIA warrants their products to be free from 
defects in material and workmanship under "normal use and 
service". This does not include normal wear and tear of parts. 
ESWOOD AUSTRALIA will repair or replace any parts, which in 
ESWOOD AUSTRALIA's sole judgement are defective in material or 
workmanship, in accordance with the warranty offered. 

 

This undertaking covers the provision of labour and parts for 12 
months from the date of delivery to the purchaser.  This undertaking 
applies only to state capitals.  Remote areas are not covered by this 
commitment and special enquires should be made. (

Note:

 

Travel 

time not covered by warranty

 

In no event will ESWOOD AUSTRALIA be liable for loss of facilities 
or other property and such things as, but not limited to, additional 
labour costs, loss of revenue or anticipated profits, and other 
damages of any kind whether direct, indirect, incidental or 
consequential. 

 

Labour under warranty is supplied free of charge during  normal 
working hours, Monday to Friday.  Should warranty work be 
requested outside or our normal working hours a labour charge will 
be applied equivalent to a normal hour rate  without out of hours 
penalty rates. (Refer to next page (1.2) of this manual for your 
closest branch for Warranty repair services)

 

 

Note: 

It is the responsibility of the owner to ensure the water feed to 

Eswood Dish and Glass washers is of a quality that will not form 
excessive build up of calcium and other dissolved minerals on the 
heating elements.  Premature failure of heating elements that exhibit 
this cause of failure will not be covered under warranty. 

Содержание ES-220














Отзывы: