Esu LokPilot Fx V4.0, Инструкция по эксплуатации

Страница: 60 / 76

60
Rule 17 Forward: Applicable only if the output is set to either •
“Dimmable headlight” or “Dimmable headlight with fade in /
out”. Causes the effect to be dimmed to around 60% of the set
brightness, if the locomotive is stopped. When the engine is run-
ning forward, the output will be increased to a 100%.
Dimmer: Causes the output to be dimmed to around 60% of the
•
defined brightness, if the global flag “Dimmer” is set. With this
function you are able to realise a full beam very easily by setting
the the global function “Dimmer” with a function key (compare
chapter 12.2.2.2).
LED mode: The light outputs are pre-set to be used with incan-
•
descent bulbs. If you wire LEDs on the output, you should set this
option in order to let the decoder know about it. The light effects
will be accordingly adjusted, so that the result will look more re-
alistic again.
Please set index register CV 31 to 16 and CV 32 to 0 before chang-
ing any of the CVs.
Please note that there are two complete sets of output configura-
tions for the headlights (light forward, backup light) and AUX1
and AUX2. This enables you to program some special effects in
conjunction with the function mapping.
In order to set each output, you should proceed as follows:
1. From the chart fig. 28 on the previous page, select the value for
the Mode Select CV.
2. Compute the value for the Special Function CV 1 by adding the
desired values you can find in the chart.
3. Define the value for the desired brightness.
4. Write the values into the CV corresponding to the appropriate
function output.
Repeat these steps for all 6 function outputs you want to con-
figure.
Example: Double Strobe with LEDs on AUX4 for a LokPilot V4.0
decoder.
We want to set up AUX4 to create a Double strobe output. We
want to use an LED.
1. Using table 28, we find that the Mode Selection CV must be
set to 6.
2. We find out that for LED compensation mode, we should set
the Special function CV to 128.
3. We want to have a brightness level of 25.
4. Using the table on the left side, we find that the Mode Select
CV for AUX4 is 299. We set CV 299 = 6. We also find that the
brightness CV is 302 and set it to 25. Finally, the Special func-
tion CV for AUX4 is 303 and needs to be set to 128.
12.3.3. Grade Crossing holding time
You can define the for time the global grade crossing function as
you like. By doing so, the “Grade Crossing” will remain active, also
after switching off the function key. This will create a very interest-
ing game effect. The desired value will be stored in CV 132. The
value of CV 132 multiplied with 0.065 seconds defines the time.
The default value 80 results in 5.2 seconds.
12.3.4. Flash rate
You can also set the flash rate for all lighting effects globally. All
effects will flash or strobe at the same rate. The desired value
should be stored in CV 112. The value of CV 112 multiplied with
0.065536 seconds (65,536ms) defines the flash rate. The default
value 30 results in 1.97 seconds.
12.3.5. Automatic Switch-off
Each output usually switches off when the corresponding key is
deactivated. However, sometimes the output has to be “forced”
to switch off after a certain period of time to aviod damages.
Digital couplers by ROCO® e.g. cannot handle permanent control.
Via the automatic switch-off function you are able to determine
for every output when it should be switched off automatically - no
matter if the function key is still activated.
Just write the time, after which the output should be switched
Function outputs