background image

 

 

SGOES Infrared Combustible Gas Detector 

820-0006 

 

Operating Manual 

 

Page 7 

 

 
2.0 Specifications and Technical Data

  

Mechanical Characteristics 

Material 

Stainless Steel (Type 316) 

Conduit Connection 

¾” NPT

 

2 connections for Field Wiring 
1 connection for HART/USB 

Dimensions 

8.01

” x 5.

3

0” x 

5.12

 (203.5mm x 134.50mm x 130mm)

 

Weight (no sensors) 

14.33lb (6.5 kg) 

Optics Protection 

Weatherproof Cover 

Electrical Characteristics 

Input Voltage 

+24VDC Nominal (+18 to 32VDC) 

Power Consumption 

7.9W Maximum 

Output From SGOES 

+4-20mA industry standard analog with embedded HART 
Digital RS-485 MODBUS RTU 
HART interface with easy access dedicated connector 

3 “Dry Contact” relays. Fault relay (NC/Form

-B), alarm level 1 (NO/Form-A), alarm level 2 

(NO/Form-A). 
All Relays Contact Rating 1Amp@125VAC/30VDC

 

Alarm Relays 

2 User Programmed Alarm Relays (factory default setting: NO) 
1 Fault Condition Programmed Relay (factory default setting: NC) 

Operational Characteristics 

Gases detected 

Methane, Propane, Butane, Pentane, Hexane,  
Isobutane, Cyclopentane, Ethanol.  
(The target gas is factory configured according to customer request.) 

Gas Detection Range 

0-100% LEL  

Accuracy 

± 2% of the full-scale gas concentration  

Response Time 
(for 100% LEL methane) 

50% full scale < 1.9 seconds  
90% full scale < 5.0 seconds 

Humidity Range 
 

Up to 95% RH, non-condensing  
(Withstands up to 100% RH for short periods) 

Warm-up time 

10 minutes 

Operating Temperature 

-40

o

 F to + 167

o

 F (-40

o

C to +75

o

C), Extended Range -76

o

 F to + 257

o

 F (-60

o

C to +125

o

C) 

Ingress Protection 

IP66 

RFI/EMI Protection 

EN50081-1 / Class B E> 50270 
*Operates with no interference from a 5 watt walkie-talkie keyed (transmitting) at 1 meter 

Status Indication 

Tri-color status LED indicates operational mode, fault, and gas presence. 

Displayed information when 
used w/ Field Control Unit 
(SSS-903 or Vector) 

Continuous sensor data  
Gas Type 
Measuring Units 
Three Fixed Alarm Thresholds 
Graphic display of trending data for Peak Readings and Time-Weighted Average (TWA) of 
gas concentration 3-30 minutes 

 

Содержание SGOES





































Отзывы: