background image

All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of 
ESERA-Automation or E-Service GmbH. Errors and technical modification subject to change. 



ESERA-Automation, E-Service GmbH 2020 

www.esera.de 

11320 V1.0 R1.0 Manual 

Page 8 of 8 

22 

Trademarks 

All mentioned designations, logos, names and trademarks (including those which are not explicitly marked) are 
trademarks, registered trademarks or other copyright or trademarks or titles or legally protected designations of their 
respective owners and are hereby expressly recognized as such by us. The mention of these designations, logos, names 
and trademarks is made for identification purposes only and does not represent a claim of any kind on the part of ESERA-
Automation, E-Service GmbH on these designations, logos, names and trademarks. Moreover, from their appearance on 
ESERA-Automation webpages it cannot be concluded that designations, logos, names and trademarks are free of 
commercial property rights. 
ESERA is a registered trademark of E-Service GmbH. 

 

23 

Contact 

ESERA-Automation 
E-Service GmbH 
Adelindastrasse 20 
87600 Kaufbeuren 
GERMANY 
Tel.: +49 8341 999 80-0 
Fax: +49 8341 999 80-10 

www.esera.de

 

[email protected]

 

WEEE-Number: DE30249510

 

 

Содержание 11320









Отзывы: