manualshive.com logo in svg

ESD E.1104.02, Руководство по оборудованию, Страница: 23 / 26

Поделиться
Скачать
ESD E.1104.02 Скачать руководство пользователя страница 23

Connector Assignments

7.2 PMC Connectors

The ECS-PMC/FPGA module uses the PMC connectors Pn1, Pn2 and Pn4. Pn1 and Pn2 provide
the PCI interface and power supply connection. Pn4 has a complete module specific pin out.

7.2.1 PMC Connector Pn1 (P11)

Signal

Pin

Signal

TCK

1

2

-12V

GND

3

4

INTA#

INTB#

5

6

INTC#

GND (BMODE1#)

7

8

+5V

INTD#

9

10

n.c. (reserved)

GND

11

12

+3.3VAUX

PCI-CLK

13

14

GND

GND

15

16

GNT#

REQ#

17

18

+5V

VIO

19

20

AD[31]

AD[28]

21

22

AD[27]

AD[25]

23

24

GND

GND

25

26

C/BE3#

AD[22]

27

28

AD[21]

AD[19]

29

30

+5V

VIO

31

32

AD[17]

FRAME#

33

34

GND

GND

35

36

IRDY#

DEVSEL#

37

38

+5V

GND (XCAP)

39

40

LOCK#

n.c. (SDONE#)

41

42

n.c. (SBO)

PAR

43

44

GND

VIO

45

46

AD[15]

AD[12]

47

48

AD[11]

AD[09]

49

50

+5V

GND

51

52

C/BE0#

AD[06]

53

54

AD[05]

AD[04]

55

56

GND

VIO

57

58

AD[03]

AD[02]

59

60

AD[01]

AD[00]

61

62

+5V

GND

63

64

n.c. (REQ64#)

For signal description please refer to the PCI Local Bus Specification 2.2.

Name

Description of Signals at Pn1

n.c.

This pin is not connected at the module.

( … )

Pins with signal names in brackets are reserved for future use. These signals are not 
supported at the moment.

ECS-PMC/FPGA

Hardware Manual • Doc. No.: E.1104.21 / Rev. 1.1

Page 23 of 26

Содержание E.1104.02



























Отзывы:

Нет отзывов