manualshive.com logo in svg

ESD CAN-CBM-REL4, Руководство по оборудованию, Страница: 12 / 26

Поделиться
Скачать
ESD CAN-CBM-REL4 Скачать руководство пользователя страница 12

Hardware Configuration

CAN-CBM-REL4 Hardware Manual Rev. 1.2

9

3. Configuration via Rotary Switches

Depending on the setting of the two rotary switches LOW (SW110) and HIGH (SW111), the CAN-
CBM-REL4 module starts with different configuration:

Default configuration 

00h :

Default configuration is stored in EEPROM 

Manual configuration 

FFh:

Parameters are selected and configured via the rotary
switches,  configuration is stored in EEPROM 

When the configuration has been finished, the module number is set via both rotary switches:

Setting the module number

01-7Fh:  CAN-CBM-REL4 module is started with the configuration

presently stored in the EEPROM. The module number
corresponds  to  the  current  position  of  the  rotary  switches
when  the  module is switched on and is not to be changed
during operation. The module is shipped with the module no.
set to 01h.

Note:

If switching the module OFF and ON, you have to wait a few seconds between switching
ON and switching OFF, because the capacitors of the local power control must be
discharged!

Содержание CAN-CBM-REL4



























Отзывы:

Нет отзывов