background image

 

 

Class II Biological Safety Cabinet 

 

   

INTRODUCTORY PAGES 

i   

Table of Contents 

iii   

Warranty Terms and Conditions 

v   

Introduction 

v   

 

1. Products Covered 

v   

 

2. Safety Warning 

v   

 

3. Limitation of Liability 

v   

 

4. European Union Directives on WEEE and RoHS 

vii   

Declaration of Conformity 

   

 

 

 

 

USER SECTION 

1   

Chapter 1 - Product Information 

1   

 

1.1 Quick View 

   

 

 

 

3   

Chapter 2 - Sentinel Control System 

3   

 

2.1 Sentinel Control System 

4   

 

2.2 Menu Options 

4   

 

 

2.2.1 Settings 

6   

 

 

2.2.2 Calibration 

6   

 

 

2.2.3 Admin 

7   

 

 

2.2.4 Set Mode 

7   

 

2.3 Alarm and Warnings 

   

 

 

 

9   

Chapter 3  - Basic Cabinet Operation 

9   

 

3.1 Sash Window Operation 

9   

 

 

3.1.1 Sash Window State 

9   

 

 

3.1.2 Operating Motorized Sash Window 

10   

 

 

3.1.3 Using Sash Window 

10

 

 

 

3.2 Starting and Shutting Down the BSC 

10

 

 

 

 

3.2.1 Turning on the BSC 

10

 

 

 

 

3.2.2 Turning off the BSC 

10

 

 

 

3.3 Working in the BSC 

11   

 

3.4 Working Ergonomics 

12   

 

3.5 UV Lamps 

12   

 

3.6 Decontamination and Disinfecting Agents 

   

 

 

 

15   

Chapter 4 - Maintenance 

15   

 

4.1 Scheduled Maintenance 

16   

 

4.2 Maintenance/Service Log 

   

 

 

 

   

 

 

APPENDIX 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

   

 

 

 

 

 

Содержание Labculture PLUS































Отзывы: