background image

 

9

62.  Press 

OK 

to accept your write in and return to the previous 

screen.   

 

63.  Review Summary Screen once all races are voted.  Press 

NEXT. 

 

64.  Press the 

MARK BALLOT 

button. 

 

65.  Remove marked ballot.  The “Insert Your Ballot” screen will appear. 

 

66.  

Proceed and Vote Ballot Using Keypad (Only) 

 

 

                        Forward/Next 

 

                         Scroll Up 
 

 

 

 

 

 

 

 

 

                         Select 
 
                         Back 
 
                         Scroll Down 
 
 

 

 

 

To write-in a candidate using the Keypad 

67.  On the Contest Screen, select 

Write-In.

  

Note:

 Press the 

LEFT Arrow

 on the Keypad to close the write-

in screen without entering a candidate and return to the contest 
screen. 

 

68.  On the Write-In Pop-Up Screen, using your Keypad, press 

UP

 and 

DOWN

 to hear each letter read.  Once you hear the 

letter you want, press 

Select

.   

 

69.  Confirm your write-in on the top of the write-in screen. 

 

 

Screen On 

Audio Repeat

Audio Speed 
- Decrease 
+ Increase 

Volume 
- Decrease 
+ Increase 

Содержание AutoMARK














Отзывы: