manualshive.com logo in svg

ES&S AutoMARK, Руководство пользователя, Страница: 3 / 13

Поделиться
Скачать
ES&S AutoMARK Скачать руководство пользователя страница 3

 

3

 

15.  Lift the entire lid away from you into a vertical position.  
The Touch Screen Monitor under the lid is now visible.  

 

16.  Lift the Touch Screen Monitor towards you into a vertical 
position.  

  

17.  Adjust the angle of the Touch Screen Monitor for viewing 
comfort. 

 

18.  Close the lid, leaving the Touch Screen Monitor in the 
upright position.  The Touch Screen Monitor is held in place by 
tension bearings which allows it to remain in the upright 
position.   

 

19.  Pull up on the Ballot Feed Tray, then pull it towards you 
and lower it into position. 

 

20.  Plug the headphones into the appropriate headphone jack in front of the 
terminal.

 

 

Cleaning the ES&S AutoMARK™

  

 

21.  Use alcohol wipes to clean the outside panels and screen of the ES&S 
AutoMARK™ unit.  Ensure the unit is dry before turning it on. 

 

 

Installing The Compact Flash Card 

 

 

 

 

 

Compact Flash 
Card 

Compact Flash 
Access Door 

Compact Flash 
Access Door 
Key

Содержание AutoMARK














Отзывы:

Нет отзывов