ESAB Cadd Tig 1500i TA34 Скачать руководство пользователя страница 24

Страница: 24 / 50

S0740 800 186/E080826/P50

-- 24 --

ct34_20

20AP1 Control board

The processor on the control board monitors and controls the various functions of the power

source. The control board is used in combi mode. In combi mode the board handles the

control of the power source, the welding data unit and the MMC panel.

If the circuit board is faulty, it must be replaced. After replacing the circuit board, soft--start

the machine. See the instructions on page 42.

There are two hardware versions of the control board, see page 32.

Note!

The spare part boards have different ordering numbers for the Tig 1500i TA34,

Tig 2200i TA33 and Tig 2200i TA34

see the spare parts list.

Circuit board identity

Power source unit

The control board has a machine ID, a hardware ID and a unit type number. To read this

you need the

ESAT

service kit, see page 37.

The machine ID defines which type of power source the board is intended for.

The hardware ID shows design and type of circuit board.

The unit type is used for identification on the CAN bus.

The ID numbers of the power sources are:

Tig 1500i

Tig 2200i

Machine ID = 33

Hardware ID = 4

Unit type = 2

Machine ID = 34

Hardware ID = 4

Unit type = 2

Welding data unit and MMC

The machine ID for the MMC part of the control board determines which type of control

panel that is used. The machine ID can be changed by ESAT.

The ID numbers of the different control panels are:
TA33 machine ID = 37

TA34 machine ID = 19
Hardware ID = 4

Unit type = 0

20AP1:1

Power supply

+5 V and +2.5 V

IC6 monitors the 24 V voltage supply to the 5 V regulator on circuit board

2AP1. IC16 monitors the 5 and 2.

V supplies. Regulator VR4 supplies the

processor with +2.

Содержание Cadd Tig 1500i TA34



















































Результаты поиска

Содержание Cadd Tig 1500i TA34

Отзывы:

Похожие инструкции для Cadd Tig 1500i TA34

Бренды по названию

Популярные бренды

ESAB Cadd Tig 1500i TA34, Руководство по обслуживанию

Результаты поиска

Содержание Cadd Tig 1500i TA34

Отзывы:

Похожие инструкции для Cadd Tig 1500i TA34

Бренды по названию

Популярные бренды