background image

 

 

The  signal  words 

CAUTION,  WARNING,

  or 

DANGER

 are used to indicate hazards. 

 

 

 

 

Indicates 

potentially 

hazardous  situation  which,  if  not  avoided, 
may result in minor or moderate injury.

 

 

 

 

Indicates 

potentially 

hazardous  situation  which,  if  not  avoided, 
could result in death or serious injury.

 

 

 

Indicates 

potentially 

hazardous  situation  which,  if  not  avoided, 
will result in death or serious injury.

 

 

 

 

The  word 

IMPORTANT

  is  used  in  the  text  when 

immediate  damage  will  occur  due  to  improper 
technique or operation.  

 

 
The word 

NOTE

 is used to convey information that 

is  out  of  context  with  the  manual  text;  special 
information  such  as  specifications,  techniques, 
reference  information,  and  other  information  of  a 
supplementary nature. 
 
 

 

The user is responsible for  inspecting the machine 
daily, and for having parts repaired or replaced when 
continued use of the machine would cause damage, 
excessive wear to other parts or make the machine 
unsafe for continued operation. 
 
If an operating procedure, tool device, maintenance 
or  work  method  not  specifically  recommended  is 
used, you must satisfy yourself that it is safe for you 
and  others.  You  must  also  ensure  that  the 
attachment will not be damaged or made unsafe by 
the procedures you choose. 
 
Erskine  Attachments  LLC  cannot  anticipate  every 
possible  circumstance  that  might  involve  potential 
hazard. The safety messages found in this manual 
and on the machine are therefore not all inclusive. 
 
Throughout this manual, reference may be made to 
the left hand (LH) and right hand (RH) side.  These 
terms are used as viewed from the operator’s seat 
facing front. 
 
 

SAFETY 

 

 

 

 

 

 
DO NOT use or perform maintenance on this machine until this manual has been 
read  and  understood.    In  addition,  read  the  Operation  and  Maintenance 
Manual(s) 

pertaining to the attachment and the attachment carrier (“Loader”).  

 

Содержание V-Plow





















Отзывы: