background image

 

 

 

                                  

USER’S MOUNTING INSTRUCTIONS

                   

 

                    

 
 7.  Connect  the  hydraulic  quick  couplers  from  the 

attachment to the loader.  
  

IMPORTANT:     

Wipe  the  ends  of  the  hydraulic 

quick couplers (both lead and loader) with a rag 
to 

remove 

any 

possible 

contamination.  

Contamination can cause hydraulic components 
to fail and is not covered under warranty. 

 
IMPORTANT:

  Make sure the quick couplers are 

fully engaged.  If the quick couplers do not fully 
engage, check to see that the couplers are the 
same  size  and  brand.    Do  not  force  the  quick 
couplers together.

 

 

NOTE:

   

See  the  loader’s  operator’s  manual  for 

auxiliary  hydraulic  specifications  and  connection 
instructions. 
 

NOTE:

   

Attachment  is  shipped  with  8FJX  (1/2” 

Female  JIC  Swivel)  fittings  on  the  ends  of  the 
lead hoses. 

 
8.  Make  sure  the  hoses  are  properly  routed  to  fit 

your specific loader.  If the hoses are not routed 
correctly, hoses may get pinched or rub on tires.  
Be sure to check the hose routing through the full 
range  of  intended  motion  of  the  attachment 
before operating it.   

 

More  than  one  routing  may  be  acceptable 
depending  on  the  loader.    Pick  the  routing  that 
best suits your loader. 

 

IMPORTANT: 

Proper  hose  routing  is  the 

responsibility  of  the  owner  and/or  operator.  
Pinched  or  stretched  hoses  are  not  covered 
under warranty. 

 

Mounting is now complete and you are ready to use 
the  attachment.    Use  reverse  order  of  above 
instructions  to  dismount  the  attachment  from  the 
loader. 

 

Содержание LS 24

















Отзывы: