Ericsson RX8200 Скачать руководство пользователя страница 14

Страница: 14 / 44

Quick Start Guide: Connect-Power-Configure

8. Set the set the LNB power output level

A description of each of these User Settings can be found in the

Reference Guide

Note:

If the unit has successfully locked to the incoming feed, then the TS Lock

value in menu

Input

should be

LOCKED

3.3.3

IP (GIGE) Input (if fitted)

Ensure that the incoming feed is connected to connector

IP IN 1

To configure the unit for IP GIGE input, navigate to the front panel

Input

menu and

carry out the following steps:

1. Select

input

2. Set the Network 1 (and Network 2, if used) IP Address

3. Set up the MAC Mode parameters

4. Set up I/P Ports settings

5. Set up Stream 1/Unicast 1 (and Stream 2/Unicast 2, if used) settings

6. Set up Alarms/Alerts settings as required.

A description of each of these User Settings can be found in the

Reference Guide

Note:

If the unit has successfully locked to the incoming feed, then the TS Lock

value in menu

Input

should be

LOCKED

3.3.4

G.703 (ATM) Input (if fitted)

Ensure that the incoming feed is connected to connector

G703

To configure the unit for G.703 ATM input, navigate to the front panel

Input

and carry out the following steps:

1. Select

G703

input

2. Set the Mode

3. Set up Destuffing/Deinterleaver

4. Set up Reed Solomon/Derandomiser

5. Set up Man Packet Length Ctrl/Packet Length Size

6. Set up ATM Delta/ATM Alpha settings

7. ATM Descrambling/Header Correction

8. ATM Header Error Ignore ATM VPI

EN/LZT 790 0009 R1A

2011-03-30

14 (44)

Содержание RX8200













































Результаты поиска

Содержание RX8200

Отзывы:

Похожие инструкции для RX8200

Бренды по названию

Популярные бренды

Ericsson RX8200, Руководство пользователя

Результаты поиска

Содержание RX8200

Отзывы:

Похожие инструкции для RX8200

Бренды по названию

Популярные бренды