Ericsson RX8200 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 44

background image

Installing the Equipment

2

Installing the Equipment

2.1

Introduction

For best performance and reliability follow the instructions for site requirements and
installation in the

Reference Guide

and only use installation accessories

recommended by the manufacturers.

Warning!

Do not remove the covers of this equipment. Hazardous voltages are present within
this equipment and may be exposed if the covers are removed. Only Ericsson
trained and approved service engineers are permitted to service this equipment.

2.2

Operating Voltage

Caution!

This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your business,
consult a qualified electrical engineer or your local power company.

Note:

Refer to the

Reference Guide

for details of the color codes used on the

mains leads.

See

for fuse information and also the

Reference Guide

for a full power

supply specification.

AC Models

AC models are fitted with a wide-ranging power supply. It is suitable for supply

voltages of 100-240 V AC -10% +6% at 50/60 Hz nominal.

2.3

Power Cable and Earthing

Check that the power cable is suitable for the country in which the Receiver is to be
used.

EN/LZT 790 0009 R1A

2011-03-30

9 (44)

«
...
7
8
9
10
11
...
»

Содержание RX8200













































Отзывы:

Нет отзывов

Похожие инструкции для RX8200

Бренд: Eclipse Страницы: 101

Бренд: Eclipse Страницы: 8

Бренд: Lectrosonics Страницы: 12

Бренд: Tait Страницы: 72

Бренд: Magnadyne Страницы: 16

Бренд: Boston Страницы: 48

Бренд: ADTRAN Страницы: 17

M1 HD + U.S Edition

Бренд: X2 Страницы: 9

Бренд: Tele System Страницы: 24

Бренд: Planet Audio Страницы: 17

Бренд: PEEKTON Страницы: 86

Бренд: PCB Piezotronics Страницы: 17

Бренд: Hammarlund Страницы: 40

Бренд: Dual Страницы: 20

Бренд: FTE Maximal Страницы: 38

Бренд: AOR Страницы: 81

Бренд: Roadstar Страницы: 21

Бренд: NAD Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды