background image

MONOGRAM SERIES WARRANTY

A.

Ericsson  Inc. (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer")
that Equipment manufactured by Seller shall be free from defects in material, workmanship and
title, and shall conform to its published specifications. With respect to any Equipment not
manufactured by Seller (except for integral parts of Seller’s Equipment to which the warranties
set forth above shall apply). Seller gives no warranty, and only the warranty, if any, given by the
manufacturer shall apply. Batteries are excluded from this warranty but are warranted under a
separate Nickel-Cadmium Battery Warranty.

B.

Seller’s obligations set forth in Paragraph C below shall apply only to failures to meet the above
warranties (except as to title) occurring within the following periods of time from date of sale to
the Buyer and are conditioned on Buyer’s giving written notice to Seller within thirty (30) days of
such occurrence:
1. for fuses, incandescent lamps, vacuum tubes and non-rechargeable batteries, operable on

arrival only.

2. for parts and accessories (except as noted in B.1) sold by Seller’s Service Parts Operation,

ninety (90) days.

3. for all other Equipment of Seller’s manufacture, two (2) years.

C.

If any Equipment fails to meet the foregoing warranties, Seller shall correct the failure at its option
(i) by repairing any defective or damaged part or parts thereof, or (ii) by making available at Seller’s
factory any necessary repaired or replacement parts. Any repaired or replacement part furnished
hereunder shall be warranted for the remainder of the warranty period of the Equipment in which
it is installed. Where such failure cannot be corrected by Seller’s reasonable efforts, the parties
will negotiate an equitable adjustment in price. Labor to perform warranty service will be provided
at no charge only for the Equipment covered under Paragraph B.3, and only during the first
twenty-four (24) months following the date of sale to the Buyer. Thereafter, labor will be charged
at prevailing rates. To be eligible for no-charge labor, service must be performed by an Authorized
Service Center or other Servicer approved for these purposes either at its place of business during
normal business hours, for mobile or personal equipment, or at the Buyer’s location, for fixed
location equipment. Service on fixed location equipment more than thirty (30) miles from the
Service Center or other approved Servicer’s place of business will include a charge for transpor-
tation. Equipment located off-shore is not eligible for no-charge labor.

D.

Seller’s obligations under Paragraph C shall not apply to any Equipment, or part thereof, which
(i) has been modified or otherwise altered other than pursuant to Seller’s written instructions or
written approval or, (ii) is normally consumed in operation or, (iii) has a normal life inherently
shorter than the warranty periods specified in Paragraph B, or (iv) is not properly stored, installed,
used, maintained or repaired, or, (v) has been subjected to any other kind of misuse or detrimental
exposure, or has been involved in an accident.

E.

The preceding paragraphs set forth the exclusive remedies for claims (except as to title) based
upon defects in or nonconformity of the Equipment, whether the claim is in contract, warranty, tort
(including negligence), strict liability or otherwise, and however instituted. Upon the expiration of
the warranty period, all such liability shall terminate. The foregoing warranties are exclusive and
in lieu of all other warranties, whether oral, written, expressed, implied or statutory. NO IMPLIED
OR STATUTORY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. IN NO EVENT SHALL THE SELLER BE LIABLE FOR ANY INCIDEN-
TAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARY DAMAGES.

This warranty applies only within the United States.

ECX-915C

1-800-528-7711 (Outside USA, 804-528-7711)

19

Содержание LBI-38862A























Отзывы: