Ericsson KPC-300, Руководство по обслуживанию

Страница: 21 / 34

5. Decrease the default Squelch_Close_MID (Squelch
Low) value until squelch closes.
6. Repeat Steps 2 thru 5 at 12.5 kHz channel spacing.
7. Select radio channel 1 at 25 kHz channel spacing.
8. Adjust Squelch _Offset_Low value until squelch
opens at 8 dB SINAD. Adjustment range should be
very small. When value is increased at 0.02 steps
(values will be 0.02, 0.06, etc.), squelch open level
goes down. When value is decreased at 0.02 steps
(values will be 4.98, 4.94, etc.), squelch open level
goes high.
9. Select radio channel 1 at 12.5 kHz channel spacing.
10. Adjust Squelch_Offset_Low value the same as Step 8.
11. Select radio channel 3 at 25 kHz channel spacing.
12. Adjust Squelch_Offset_High value the same as Step
8.
13. Select radio channel 3 at 12.5 kHz channel spacing.
14. Adjust Squelch_Offset_High value the same as Step
8.
TCXO
1. Connect Communications Monitor to radio.
2. Key the radio and monitor the transmitter frequency
stability.
3. Adjust TCXO reference voltage using the PC Pro-
gramming Software to get required transmitter fre-
quency (typical voltage should be 2.20V, adjustable
range is between 2.00 and 2.40 V).
BATTERY INFORMATION
CHARGE BEFORE USING
Insert the radio into the slot on the charger and ensure that
the ON/OFF/VOLUME control is in the OFF position. Con-
nect charger to a 120 VAC outlet. Charge the battery for the
first time at least 14 hours but no longer than 48 hours.
Over-charging may reduce battery life.
RECHARGING THE BATTERY
Recharge the battery when you experience difficultity in
receiving or sending a message. Also the battery may need
recharging when the red TX indicator is blinking.
Chargers are available with nominal charge times of one
to 14 hours. Combinations include single and multiposition
chargers. When charging a battery pack that is attached to a
radio, always turn the radio OFF to ensure a full charge. For
specific instructions, refer to the applicable charger Opera-
tor’s Manual. Charging in non-Ericsson equipment may lead
to battery damage and void the battery warranty.
Batteries which have been stored (charged or discharged)
will generally not be capable of full capacity until the batter-
ies have been fully cycled two or three times. (Charging the
battery in an Ericsson rapid charger and then discharging the
battery pack with the radio until low battery is indicated is
considered one cycle.)
INSTALLING THE BATTERY PACK
1. Ensure the ON/OFF/VOLUME control knob is in the
OFF (detent) position.
2. Align the battery pack tabs with the battery mounting
plate slots on the back of the radio (see Figure 6).
3. Insert the tabs into the slots, push down and slide the
battery toward the battery latch until the battery latch
clicks into place.
REMOVING THE BATTERY PACK
1. Ensure the ON/OFF/VOLUME control know is in the
OFF (detent) positon.
2. Press the battery release button to release the battery.
3. Remove the battery pack by sliding it back until it
stops. Then lift up and away until it separates from the
radio.
BATTERY CARE & MAINTENANCE
•
Your charger is intended for indoor use only. Keep
the charger and/or wall cube dry. Do Not use in or
near water.
•
Never let the battery contacts touch metal objects
that could short-circuit the contacts. For example,
keys or coins in your pocket.
•
Do Not disassemble a battery.
•
Do Not dispose of a battery in a fire.
•
Use only the supplied or specified battery and
charger.
•
Periodically condition your battery for improved
battery capacity and performance.
Figure 6 - Installing And Removing The Battery Pack
AE/LZB 119 1874 R1A
21