Ericsson EDACS Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

Ericsson EDACS Series Скачать руководство пользователя страница 29

LBI-38962

29

On the IMC/CEC, the EDG audio lines are connected to an audio concentrator panel using an audio concentrator
cable. The concentrator panel has four Champ connectors of which only two (J9 & J10) can be used for the EDG
audio lines.

J7

J9

J8

Can be used for EDG

Audio Concentrator

J10

J2

J3

J1

J6

J4

J5

Audio Interface

Breakout Connectors

(on reverse side)

Panel

IMC Audio Concentrator Panel

Each Breakout Connector supports up to 4 EDG ports. The table below shows the mapping between a Champ
connector and its Breakout Connectors for the EDG audio interface. The first Breakout Connector that is used is
plugged into the DIM Audio Board closest to the DIM Controller Board.

Breakout Connector

Champ Connector

Used

First Four EDG

Ports

Additional Four

EDG Ports

J9

J2

J3

J10

J4

J5

Champ to Breakout Connector Mapping

Use the following procedure to connect the data lines between the EDG and the IMC.

1)

Locate the Champ connector labeled C01 on the rear of the EDG modem rack. Plug one end of the Audio
Concentrator Cable into the connector.

2)

Locate the Champ J9( or J10) connector on the IMC audio concentrator panel assigned to the EDG.
Plug the other end of the Audio Concentrator Cable into the connector.

A cable should run from each breakout connector used to a DIM Audio Board associated with the DIM
Controller Board that was connected in the previous section.

«
...
27
28
29
30
31
...
»

Содержание EDACS Series









































Отзывы:

Нет отзывов