background image

INTRODUCTION

This manual contains installation instructions for the EDACS

MONOGRAM SERIES Mobile Radio, Desktop Station, and associated
accessories. These instructions cover the mounting and cabling of the mobile
radio and station setup. Interconnection diagrams are located at the back of the
manual for your reference. Before installation, the radio should be
programmed using an IBM compatible personal computer and the following
items:

Programming Cable

RPM 113 2510/1

Programming Software

AE/LZY 213 766

UNPACKING AND CHECKING EQUIPMENT

The EDACS MONOGRAM SERIES Radio may be provided for either

station or mobile applications. When ready for installation, carefully unpack
the radio and identify each item in the shipping container. If damage has
occurred to the equipment during shipment, file a claim with the carrier
immediately.   The available options for the Mobile Radio are identified in
Table 1.

MOBILE EQUIPMENT

EDACS MONOGRAM SERIES Mobile Radio  .  .  KRD 103 123/2

Microphone .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  MGMC5X

Microphone Hangar and Mounting Hardware  .  .  .  TBD

PowerCable,8 feet  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  RPM 113 2509/1

Mobile Mounting Bracket 
and Associated Hardware  .  .  .  .  .  .  .  .  .  .  .  .  .  SXA 120 4253/1

Operator’s Manual..  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  AE/LZT 123 1920

Installation Manual  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  AE/LZT 123 1921

STATION EQUIPMENT (In addition to Radio)

Power supply  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  MGPS5V

Station Microphone  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  MGMG7A

3

Содержание EDACS Monogram Series

















Отзывы: