background image

Introduction and regulations

3

§

§

Dear Client,
In selecting a JK-Ergoline sunbed you have acquired a high-performance appliance featuring ad-
vanced technology. Your sunbed has been manufactured with the greatest care and precision,
having undergone numerous quality controls and safety checks. We have done everything to en-
sure the trouble-free and reliable operation of your sunbed.
However, you also can do a lot to ensure prolonged satisfaction with your sunbed. Please read all
of the information carefully.
However, in the event that you should encounter problems with your sunbed, please contact your
local dealer.

DIRECTIVES
This JK-Ergoline sunbed has been manufactured in line with the following regulations:

 

EC Directive on "Electromagnetic compatibility" 89/336/EEC (as amended)

 

Low-voltage Directives 73/23 EEC (as amended)

NOTE
Please note that these sunbeds are intended safely for the European market and must
not be exported to the USA or Canada or operated there. No liability will be accepted in
the event of any failure to observe this notice.

In addition to these operating instructions, also observe generally applicable codes of practice,
statutory regulations and other rules - also in the country of operation - as well as the relevant pro-
visions laid down in environment law.
Attention must always be paid to the local provisions issued by the employers' liability insurance
association or other supervisory authorities.

Meaning of symbols

Hazard warnings:

CAUTION (where persons are at risk)
ATTENTION (where the sunbed is subject to potential damage)

DIRECTIVES / Statutory provisions

CAUTION / Electrical voltage

NOTE / Information

Safety and hazard warnings

 

The JK sunbed must only be assembled and installed by appropriately trained / experienced
personnel.

 

All hazard and safety warnings affixed to the sunbed must be observed.

 

None of the safety devices and safety warnings possibly affecting the safe operation of the
sunbed must be removed or taken out of operation.

 

The sunbed must only be operated if it is in perfect working order.

NOTE
The safety, reliability and performance of the sunbed will only be guaranteed if:

 

it has been installed, connected to the electrical supply, upgraded or repaired by a
locally approved firm of electricians or appropriately trained personnel,

 

electrical installation complies with the national regulations

 

and the sunbed is used in accordance with these operating instructions.

!

Содержание Ergoline 500 Series






































Отзывы:

Похожие инструкции для Ergoline 500 Series