background image

FOR CHARGER

1.  This appliance is not intended for use by persons (including children) with reduced

 

physical,sensory or mental capabilities, or lack of experience and knowledge, unless they 

 

have been given supervision or instruction concerning use of the appliance by a person 

 

responsible for their safety. Children should be supervised to ensure that they do not play 

 

with the appliance.

2.  Charger is double insulated for additional electrical safety.

3.  Charger is for indoor use only.

4.  If the charger supply cord is damaged, it must be replaced by the manufacturer, its service   

agent or similarly qualified persons in order to avoid a hazard.

5.  Never charge damaged batteries as these can short circuit and over heat.

6.  When the charger is in use it MUST be supervised , if there is any evidence of overheating    

then IMMEDIATELY disconnect the charger from the power supply.

7.  If gas or smoke is emitted from the battery during charging switch off the power supply , 

and move to a well vented area to allow the fumes to vent to atmosphere. 

 

Caution is there is leaking liquid from the battery wear protective clothing, glasses and 

clothes as this can be acidic. 

8.  Always disconnect battery charger and remove battery from charger when the charging is complete. 

9.  Only use the battery charger specifically stated on the base of the battery.

FOR BATTERY

1.  Always remove the battery pack from the charger immediately after re-charging is 

 

completed.

2.  When not in use, remove a charged battery pack from the charger.

3.  Do not charge a damaged battery pack.

4.  Do not charge non-rechargeable batteries.

5.  Do not install the battery backwards so the polarity is reversed.

6.  Do not connect the positive terminal and negative terminal of the battery to each other with  

any metal object (such as wire).

7.  Do not carry or store battery together with necklaces, hairpins or other metal objects.

8.  Do not pierce the battery with nails, strike the battery with a hammer, step on the battery or  

otherwise subject it to strong impacts or shocks.

9.  Do not solder directly onto the battery.

10. Do not expose battery to water or salt water, or allow the battery to get wet.

11. Do not disassemble or modify the battery. The battery contains safety and protection  

devices, which, if damaged, may cause the battery to generate heat, explode or ignite. The  

protection circuit module provided with battery packs is not to be used as a substitute for a  

shut-off switch.

12. Do not place the battery in or near fire, on stoves or other high temperature locations. Do  

not place the battery in direct sunlight, or use or store the battery inside cars in hot weather.  

Heating the battery can damage the safety circuitry, which can cause additional heating,  

rupture or ignition of the battery. Using the battery in this manner may also result in a loss of  

performance and a shortened life expectancy.

13. Do not place the battery in microwave ovens, high-pressure containers or on induction

 

cookware.

14. If you intend to store a battery for a period without use then store battery at room   

temperature (19°C to 25°C), charged to about 30 – 50% of capacity. When storing for very  

long periods boost-charge the battery once per year to prevent over discharge.

15. Always charge the battery in a temperature range of 0°C to 30°C and discharge in a

 

temperature range of 0°C to 75°C.

16. The battery pack and charger will be warm during charging, this is normal.

17. Do not continue charging the battery if it does not recharge within the specified charging  

Содержание ERI490CSW

























Отзывы: