Equalizer FA1TM Скачать руководство пользователя страница 10

Страница: 10 / 18

OPERATOR INSTRUCTION MANUAL

IM_FA1TM_Rev08_A4

FA1TM

FLANGE ALIGNMENT TOOL

STORAGE AND TRANSPORTATION

Equalizer tools should be stored in a cool, dry

place. Tools should always be cleaned, serviced and

lubricated prior to storage. Ensure that tools are

stored in their designated packing cases.

LONG-TERM STORAGE - MAINTENANCE PLAN

Rub components down with a dry cloth to remove

moisture.

Coat EVERY surface and contact point with a corrosion

inhibitor. Where necessary, coat inside and outside of

component

Nuts and threads must also be coated with a corrosion

inhibitor.

4. Once surfaces have been coated, seal individual

components in clear plastic bags or clear vacuum

bags or clear shrink wrap.

NOTE: bags/shrink wrap must be clear for visibility.

Take care when using shrink wrap that the tool is/

components are still easy to see.

Remove all or, where not vacuum sealed, as much air

from bags as possible.

Once bags have been closed and sealed DO NOT re-

open. Any visual inspections must be done with closed

and sealed bags. If bags are opened the components

will have to be dried, re-coated and re-sealed in bags/

shrink wrap.

7. Replace silica gel (100g) EVERY TIME the case is

opened.

NOTE: depending on moisture content of air, silica gel

should be changed weekly.

Visually inspect kits after 30-days and every 30-days

thereafter. Remember to replace silica gel before

closing case.

Secure the tool upright on a bench.

Using a small flat screwdriver, lever out one circlip

and unscrew 6 x 6mm hex screws.

Remove cover plate and remove any dirt or corrosion

from moving parts.

Inspect components for wear and damage, replace if

necessary! If there’s no damage present, then they

can be greased and re-assembled by reversing the

previous steps.

Recommended grease –

Rocol Sapphire Hi-Load or equivalent good quality hi

load bearing grease.

CIRCLIP

HEX

SCREW

COVER

PLATE

DRIVEN

WEDGE

NEEDLE

BEARINGS

DRIVING

WEDGE

Содержание FA1TM



















Результаты поиска

Содержание FA1TM

Отзывы:

Бренды по названию

Популярные бренды

Equalizer FA1TM, Инструкция оператора

Результаты поиска

Содержание FA1TM

Отзывы:

Бренды по названию

Популярные бренды