Epson Stylus Color 670 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 152

background image

EPSON Stylus COLOR 670

Revision A

Adjustment

Using the Adjustment Program

115

5.3.8 USB ID Input

Perform this adjustment when the MAIN board is replaced. EPSON Stylus
COLOR 670 stores 18-figure USB ID unique to the machine in EEPROM on
the MAIN board. USB ID is the data used when USB port is generated
when the printer is connected to the PC. Because the printer has the USB
ID, even if several printers with the same name are connected to the one
PC, the hard device driver can generate individual USB port based on
USB ID to supervise each port correctly. The following is the procedure of
inputting USB ID.

1.

Select and click “USB ID check/input” from the Adjustment menu. The
following screen appears.

Figure 5-20. Main USB ID check/input Screen

2.

Select “Input USB ID” from USB ID Input main menu and click OK.

C H E C K

P O I N T

n

When inputting the USB ID, input the data referring to the
10-digit product serial number labeled on the back of the
printer. The rest 8-digit will be automatically generated by
the adjustment program.

n

This data input is required only when the MAIN board is
replaced.

n

USB is the valid interface only under Windows98
environment.

«
...
113
114
115
116
117
...
»

Содержание Stylus Color 670

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stylus Color 670

Бренд: TE Connectivity Страницы: 7

Бренд: ?HC Страницы: 2

Бренд: TREND Страницы: 32

eFlow 104N Series

Бренд: EFLOW Страницы: 16

BiDi-Power Series

Бренд: tams elektronik Страницы: 16

Бренд: KEPCO Страницы: 2

Бренд: Cleco Страницы: 16

Бренд: OLI Страницы: 2

Accelerator 2000

Бренд: Rapid Страницы: 76

Бренд: Kamasa-TOOLS Страницы: 12

POWERPLUS POWX1331LI

Бренд: VARO Страницы: 13

Бренд: Hach Страницы: 32

Бренд: Hakko Electronics Страницы: 8

Бренд: Corsair Страницы: 42

Бренд: Grizzly Страницы: 80

Бренд: Extech Instruments Страницы: 19

Бренд: TDK-Lambda Страницы: 23

Бренд: Daiwa Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды