Epson S5U1C60N08E, Руководство пользователя

Страница: 9 / 20

S5U1C60N08E MANUAL
EPSON
3
(EVALUATION BOARD FOR S1C60N08)
3 NAMES AND FUNCTIONS OF PARTS
3 NAMES AND FUNCTIONS OF PARTS
This section describes the names and functions of the parts of the S5U1C60N08E.
3.1 Basic Functions
The S5U1C60N08E has the following basic functions:
■
Program execution (Run function)
Install the EPROM containing the application program and execute the program.
■
Interface with ICE
The S5U1C60N08E can interface with the ICE so that a higher level debugging environment may be
established.
■
Setting hardware options by installing function option and segment option ROMs
Hardware options, i.e., I/O ports and segments, can be specified by writing option data for the
function option created by the function option generator and the segment option created by the
segment option generator into EPROM, and installing the EPROM.
3.2 Functions of Parts
3.2.1 Front panel
▲
Position of pin 1
Fig. 3.2.1.1 Front panel
EVA6008
E0C6008 EVALUATION BOARD
EPSON
LCDEMU
I/O
#
1
I/O
#
0
LC
D
#
0
LC
D
#
1
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • •
■
Connectors
• I/O #0, I/O #1
Connector for the I/O cable. The I/O cable
is used to connect the S5U1C60N08E to the
target system.
• LCD #0, LCD #1
Connector for the LCD cable. The LCD cable
is used to connect the S5U1C60N08E to the
target system. LCD #1 cannot be used.
• LCDEMU
Connector for the LCD emulator cable.
3.2.2 Rear panel
DC IN
+5V GND
O I
POWER SW
F1
F5
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • • • •
▲
Position of pin 1
Fig. 3.2.2.1 Rear panel
■
Switch
• POWER SW
This is a switch to turn on (I) or off (O) the
external power supply to S5U1C60N08E.
(Please turn off the POWER switch when
ICE is connected.)
■
Connectors
• DC IN 5 V
This is a connector with external power
supply source. The external power supply
should be in direct current of 5 V for 3 A or
more.
Note: Be sure to disconnect external power source
before connection with ICE, because power is
supplied from ICE when you connect
S5U1C60N08E to ICE.
• F1, F5
Connectors for the ICE interface cable.