Epson LX-1170 Скачать руководство пользователя страница 84

Страница: 84 / 129

LX-300+/1170

Revision C

Disassembly and Assembly

4.2.7.4 Ribbon Feed Mechanism Removal

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

Remove the tension spring, 8.10 from the motor bracket and release the tension of the
timing belt. (See 4.2.7.1 "CR Motor Assembly Removal".)

Release 3 hooks securing the RD cover to the left frame.

Remove the RD cover.

Figure4-17. Ribbon Feed Mechanism Removal

4.2.7.5 RPE Sensor Removal

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

Remove the hook of the RPE sensor installed at the paper guide.

Remove RPE sensor.

Remove the harness from the RPE sensor (white).

Figure4-18. RPE/BPE Sensor Removal

4.2.7.6 BPE Sensor Removal

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

Remove the hook of the BPE sensor installed at the paper guide.

Remove BPE sensor.

Remove the harness from the BPE sensor (yellow).

Left frame

Driven pulley assy.

RD ratchet

Gear, 13.2

Base frame

RD cover

Planetary lever assy.

Timing belt

Combination gear, 51, 16.2

Timing belt

RPE sensor (white)

Paper guide

BPE sensor (yellow)

Содержание LX-1170


































































































































Результаты поиска

Содержание LX-1170

Отзывы:

Похожие инструкции для LX-1170

Бренды по названию

Популярные бренды

Epson LX-1170, Руководство по обслуживанию

Результаты поиска

Содержание LX-1170

Отзывы:

Похожие инструкции для LX-1170

Бренды по названию

Популярные бренды