Epson LX-1170 Скачать руководство пользователя страница 23

Страница: 23 / 129

LX-300+/1170

Revision C

PRODUCT DESCRIPTION

Interface Specifications

1.3.2 Parallel Interface (Reverse Channel)

Transmission mode:

IEEE-1284 nibble mode

Adaptable connector:

See 1.3.1 "Parallel Interface (Forward Channel)"

Synchronization:

Refer to the IEEE-1284 specification

Handshaking:

Refer to the IEEE-1284 specification

Signal level:

IEEE-1284 level 1 device

See 1.3.1 "Parallel Interface (Forward Channel)"

Data transmission timing:

Refer to the IEEE-1284 specification

Extensibility request:

The printer responds to the extensibility request

affirmatively, when the request is 00H or 004H, which means;

00H: Request for nibble mode of reverse channel transfer
04H: Request device ID in nibble mode of reverse channel transfer

Device ID: The printer sends following device ID string when it is requested.

When IEEE1284.4 is enabled;

When IEEE1284.4 is disabled;

[00H][4EH]
MFG: EPSON;
CMD: ESCPL2,PRPXL24,BDC,D4;
MDL: LX-300+;
CLS: PRINTER;
DES: EPSON[SP]LX-300+;

[00H][4EH]
MFG: EPSON;
CMD: ESCP9,PRPII9,BDC,D4;
MDL: LX-1170;
CLS: PRINTER;
DES: EPSON[SP]LX-1170;

LX-300+

LX-1170

[00H][4BH]
MFG: EPSON;
CMD: ESCPL2,PRPXL24,BDC;
MDL: LX-300+;
CLS: PRINTER;
DES: EPSON[SP]LX-1170;

[00H][4BH]
MFG: EPSON;
CMD: ESCP9,PRPII9,BDC;
MDL: LX-1170;
CLS: PRINTER;
DES: EPSON[SP]LX-1170;

LX-300+

LX-1170

Table 1-13. Connector Pin Assignment and Signals (Reverse Channel)

Pin No.

Signal Name

Return
GND
Pin

In/Out

Functional Description

HostClk

Host clock signal.

DATA1

Parallel input data to the printer.

bit0:LSB

DATA2

bit1

DATA3

bit2

DATA4

bit3

DATA5

bit4

DATA6

bit5

DATA7

bit6

DATA8

bit7:MSB

PtrClk

Out

Printer clock signal.

PtrBusy/DataBit-

3,7

Out

Printer busy signal and reverse channel
transfer data bit 3 or 7.

AckDataReq/

DataBit-2,6

Out

Acknowledge data request signal and
reverse channel transfer data bit 2 or 6.

Xflag/

DataBit-1,5

Out

X-flag signal and reverse channel
transfer data bit 1 or 5.

HostBusy

Host busy signal.

-INIT

Not used.

-DataAvail/
DataBit-0,4

Out

Data available signal and reverse channel
transfer data bit 0 or 4.

1284-Active

1284 active signal.

Logic-H

Out

This line is pulled up to +5V through 3.9
k

Ω

resister.

+5V

Out

This line is pulled up tp +5V through 1.0
k

Ω

resister.

Содержание LX-1170


































































































































Результаты поиска

Содержание LX-1170

Отзывы:

Бренды по названию

Популярные бренды

Epson LX-1170, Руководство по обслуживанию

Результаты поиска

Содержание LX-1170

Отзывы:

Бренды по названию

Популярные бренды