Epson LX-1170 Скачать руководство пользователя страница 47

Страница: 47 / 129

LX-300+/1170

Revision C

Operating Principles

Printer Mechanism

2.2.1 Printhead

The table below shows the printhead specifications.

Figure 2-3. Wire Configuration

2.2.1.1 Buzzer Function

This printhead also works as a buzzer. The table below is buzzer specification.

Table 2-1. Printhead Specifications

Item

Specification

Number of wires

Diameter of wire

0.29 mm

Wire configuration

See Figure 2-3 "Wire Configuration".

Note: The figure is seen from the back of the head
facing printing side.

Direct current coil resistance

33.3 ±3.3

Ω

(25°C)

Head drive method

Rated voltage drive

Head drive voltage

35+2.1/-3.5 V

Peak current

• Normal:

0.75 A (Standard)

• Copy:

0.85 A (Standard)

1.0 A (Maximum)

Head drive frequency

• Normal:

1350Hz or less

• Copy:

1350Hz or less

Head life

• Black ribbon: 0.2 billion stroke/ wire or more

• Color ribbon: 0.1 billion stroke/ wire or more

Environmental condition

• Temperature: 5 to 55°C

• Humidity:

10 to 85%

Table 2-2. Buzzer Function -- Specification

Item

Specification

Head voltage

35 +2.1 / -3.5 V

Drive frequency

2kHz, 1.5kHz

Содержание LX-1170


































































































































Результаты поиска

Содержание LX-1170

Отзывы:

Похожие инструкции для LX-1170

Бренды по названию

Популярные бренды

Epson LX-1170, Руководство по обслуживанию

Результаты поиска

Содержание LX-1170

Отзывы:

Похожие инструкции для LX-1170

Бренды по названию

Популярные бренды