Epson EPL-N2000 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 242

background image

Busy/PtrBusy/PeriphClk

Compatibility mode: High signal indicates that the printer is not ready to
receive data.

negotiation phase: Reflects the BUSY status of the forward channel.

reverse data transfer phase: In nibble mode, this signal serves as nibble
data bit 3 and then 7.

reverse idle phase: Reflects the BUSY status of the forward channel.

ECP mode: Used for forward direction flow control. In reverse direction,
this signal is used as a ninth data bit that indicates whether the data
signals indicates a command or data.

PError/AckDataReq/nAckReverse

Compatibility mode: High signal indicates that a feed jam occurred in the
paper supply section, or that there is no paper in the paper tray.

negotiation phase: High signal indicates whether or not IEEE 1284 is
supported or not. Afterwards, this signal conforms with nDataAvail
(nFault).

reverse data transfer phase: In nibble mode, this signal serves as nibble
data bit 2 and then 6.

reverse idle phase: High until the host requests a data transfer.
Afterwards, this signal conforms with nDataAvail (nFault).

ECP mode: Low signal authorizes nReverseRequest. The host looks at this
signal in order to determine whether or not it has permission to drive the
data signals.

Select/Xflag

Compatibility mode: Always high.

negotiation phase: Xflag indicates the extensibility flag. Used to respond
to the extensibility request value sent from the host.

reverse data transfer phase: In nibble mode, this signal serves as nibble
data bit 1 and then 5.

reverse idle phase: Same as negotiation phase.

ECP mode: Same as negotiation phase.

R

Albatross Rev.c

A5 size

Appendix A

96/08/23

pass 0

Technical Specifications

A-9

«
...
171
172
173
174
175
...
»

Содержание EPL-N2000



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EPL-N2000

Бренд: Canon Страницы: 86

Бренд: Canon Страницы: 20

Бренд: GCC Technologies Страницы: 63

Бренд: gCreate Страницы: 9

Бренд: GCC Technologies Страницы: 9

Бренд: GCC Technologies Страницы: 12

Бренд: gCreate Страницы: 21

Бренд: GCC Technologies Страницы: 199

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 455

Бренд: TallyGenicom Страницы: 92

Бренд: Datamax Страницы: 95

Mark II E-4205e

Бренд: Datamax Страницы: 72

Delta Rostock mini G2 pro

Бренд: Geeetech Страницы: 89

MAGICARD 300plus

Бренд: Ultra electronics Страницы: 45

Aficio SP C240SF

Бренд: Ricoh Страницы: 14

Бренд: Muratec Страницы: 6

Бренд: Patton electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды