Epson EPL-N2000 Скачать руководство пользователя страница 141

Страница: 141 / 242

Option Problems

The message

Illegal AUX I/F Card

Illegal I/F Module

appears

The message

Illegal AUX I/F Card

means that the printer

cannot read the installed optional interface card. Turn off the
printer, then remove the card.

The message

Illegal I/F Module

means that the printer

cannot read the installed optional LocalTalk/Serial module.
Turn off the printer, then remove the module.

Illegal AUX I/F Card

indicates both the LocalTalk/Serial

module (set in LocalTalk) and the LocalTalk Type B I/F card
are installed simultaneously. Remove one of them.

Make sure the I/F card is listed in the table of installable ones
in Appendix A.

Paper does not feed from the optional lower paper cassette

Be sure you have selected the proper paper tray in your
software.

There may be no paper in the lower paper cassette. Load it
with paper.

Be sure that the lower paper cassette is properly installed and
that you have not tried to load it with too many sheets of
paper. The cassette can hold a maximum of 500 sheets or 250
sheets (depending on the tray) of 75g/m

(20 lb) paper.

The lower paper cassette may not be installed properly. See
Chapter 3 for instructions on installing the lower paper cassette.

Albatross Rev.c

A5 size

Chapter 6

96/08/23

Pass 0, DR

Troubleshooting and Maintenance

6-15

Содержание EPL-N2000



















































































































































































































































Результаты поиска

Содержание EPL-N2000

Отзывы:

Похожие инструкции для EPL-N2000

Бренды по названию

Популярные бренды

Epson EPL-N2000, Справочное руководство

Результаты поиска

Содержание EPL-N2000

Отзывы:

Похожие инструкции для EPL-N2000

Бренды по названию

Популярные бренды