manualshive.com logo in svg

Epson Buzzer S1C31D51, Техническое руководство

Техническое описание Epson Buzzer S1C31D51 доступно для бесплатного скачивания на нашем сайте. Этот генератор импульсов подходит для широкого спектра приложений и оснащен подробным техническим руководством. Скачайте его с нашего веб-сайта для полного понимания функций и возможностей этого продукта.

Поделиться
Скачать
background image

4  MEMORY AND BUS

S1C31D50/D51 TECHNICAL MANUAL

 

Seiko Epson Corporation 

4-9

(Rev. 2.00)

Peripheral circuit

Address

Register name

12-bit A/D converter 

(ADC12A) Ch.0

0x0020 07b6 ADC12A_0DMAEN5 ADC12A Ch.0 DMA Request Enable Register 5

0x0020 07b8 ADC12A_0DMAEN6 ADC12A Ch.0 DMA Request Enable Register 6

0x0020 07ba ADC12A_0DMAEN7 ADC12A Ch.0 DMA Request Enable Register 7

0x0020 07bc ADC12A_0ADD

ADC12A Ch.0 Result Register

R/F converter (RFC) Ch.0

0x0020 0840 RFC_0CLK

RFC Ch.0 Clock Control Register

0x0020 0842 RFC_0CTL

RFC Ch.0 Control Register

0x0020 0844 RFC_0TRG

RFC Ch.0 Oscillation Trigger Register

0x0020 0846 RFC_0MCL

RFC Ch.0 Measurement Counter Low Register

0x0020 0848 RFC_0MCH

RFC Ch.0 Measurement Counter High Register

0x0020 084a RFC_0TCL

RFC Ch.0 Time Base Counter Low Register

0x0020 084c RFC_0TCH

RFC Ch.0 Time Base Counter High Register

0x0020 084e RFC_0INTF

RFC Ch.0 Interrupt Flag Register

0x0020 0850 RFC_0INTE

RFC Ch.0 Interrupt Enable Register

Sound DAC (SDAC)

0x0020 0860 SDACCLK

SDAC Clock Control Register

0x0020 0862 SDACCTL

SDAC Control Register

0x0020 0864 SDACMOD

SDAC Mode Register

0x0020 0866 SDACDAT

SDAC Data Register

0x0020 0868 SDACINTF

SDAC Interrupt Flag Register

0x0020 086a SDACINTE

SDAC Interrupt Enable Register

HW processor (HWP)

0x0020 08a2 HWPCTL

HWP Control Register

0x0020 08a4 HWPINTF

HWP Interrupt Flag Register

0x0020 08a6 HWPINTE

HWP Interrupt Enable Register

0x0020 08a8 HWPCMDTRG

HWP Command Trigger Register

DMA controller (DMAC)

0x0020 1000 DMACSTAT

DMAC Status Register

0x0020 1004 DMACCFG

DMAC Configuration Register

0x0020 1008 DMACCPTR

DMAC Control Data Base Pointer Register

0x0020 100c DMACACPTR

DMAC Alternate Control Data Base Pointer Register

0x0020 1014 DMACSWREQ

DMAC Software Request Register

0x0020 1020 DMACRMSET

DMAC Request Mask Set Register

0x0020 1024 DMACRMCLR

DMAC Request Mask Clear Register

0x0020 1028 DMACENSET

DMAC Enable Set Register

0x0020 102c DMACENCLR

DMAC Enable Clear Register

0x0020 1030 DMACPASET

DMAC Primary-Alternate Set Register

0x0020 1034 DMACPACLR

DMAC Primary-Alternate Clear Register

0x0020 1038 DMACPRSET

DMAC Priority Set Register

0x0020 103c DMACPRCLR

DMAC Priority Clear Register

0x0020 104c DMACERRIF

DMAC Error Interrupt Flag Register

0x0020 2000 DMACENDIF

DMAC Transfer Completion Interrupt Flag Register

0x0020 2008 DMACENDIESET

DMAC Transfer Completion Interrupt Enable Set Register

0x0020 200c DMACENDIECLR

DMAC Transfer Completion Interrupt Enable Clear Register

0x0020 2010 DMACERRIESET

DMAC Error Interrupt Enable Set Register

0x0020 2014 DMACERRIECLR

DMAC Error Interrupt Enable Clear Register

4.5.1  System-Protect Function

The system-protect function protects control registers and bits from writings. They cannot be rewritten unless write 
protection is removed by writing 0x0096 to the SYSPROT.PROT[15:0] bits. This function is provided to prevent 
deadlock that may occur when a system-related register is altered by a runaway CPU. See “Control Registers” in 
each peripheral circuit to identify the registers and bits with write protection. 

Note

:  Once write protection is removed using the SYSPROT.PROT[15:0] bits, write enabled status is 

maintained until write protection is applied again. After the registers/bits required have been al-

tered, apply write protection.

4.6  Instruction Cache

This IC includes an instruction cache. Enabling the cache function translates into reduced current consumption, as 
the Flash memory access frequency is decreased.
This function is enabled by setting the CASHECTL.CACHEEN bit to 1. Setting this bit to 0 clears the instruction 
codes stored in the cache.

Содержание Buzzer S1C31D51










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Buzzer S1C31D51

Eaton SC100 Operation Handbook preview
SC100
Бренд: Eaton Страницы: 86
Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Бренд: Bartlett Страницы: 5
Hach sc200 Software Update preview
sc200
Бренд: Hach Страницы: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Бренд: Hach Страницы: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Бренд: Hach Страницы: 472
Hach sc1000 User Manual preview
sc1000
Бренд: Hach Страницы: 64
Hach SC4500 Basic User Manual preview
SC4500
Бренд: Hach Страницы: 210
National Instruments RMC-8354 User Manual preview
RMC-8354
Бренд: National Instruments Страницы: 102
NAU ROBOTICS RC40A Operating Instruction preview
RC40A
Бренд: NAU ROBOTICS Страницы: 109
Native Instruments Maschine Mikro MK2 Getting Started preview
Maschine Mikro MK2
Бренд: Native Instruments Страницы: 181
Omega PHCN-37 User Manual preview
PHCN-37
Бренд: Omega Страницы: 56
Omega DP25-TC Quick Start Manuals preview
DP25-TC
Бренд: Omega Страницы: 2
Watts KONTACT Manual preview
KONTACT
Бренд: Watts Страницы: 17
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Бренд: Invertek Страницы: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Бренд: Techtrol Страницы: 4
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Бренд: Webasto Страницы: 8
NCE CAB-04p Operation Manual preview
CAB-04p
Бренд: NCE Страницы: 4
Vector TCI-W13-U Manual preview
TCI-W13-U
Бренд: Vector Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды