background image

                                         

BEIJING EPSOLAR TECHNOLOGY CO.,LTD. 

10

 

5. Protection

 

Protection 

Instruction

 

PV Overcurrent 

When  the  charging  current  of  the  PV  array  exceeds  the 
controller

’s  rated  current,  it  will  be  charged  at  the  rated 

current. 

PV Overvoltage 

When the voltage of PV will exceed 50V, the controller will 
stop charging and restart to charge when the PV voltage is 
below 45V 

PV short circuit 

When  the  PV  voltage  is  below  50V  and  short  circuit,  the 
controller will stop charging; the controller restart to charge 
when the fault is cleared, it doesn

’t damage the controller.   

PV Reverse 
Polarity 

When  the  polarity  of  the  PV  array  is  reversed,  the 
controller  may  not  be  damaged  and  can  continue  to 
operate normally after the polarity is corrected. 

 

Night Reverse 
Charging   

Prevents the battery from discharging to the PV module at 
night.

 

Battery Reverse 
Polarity 

Fully protected against battery reverse polarity; no damage 
will occur to the battery. Correct the wiring error to resume 
normal operation. 

Battery   
Overvoltage

 

When  the  battery  voltage  reaches  the  overvoltage 
disconnect  voltage,  it  will  automatically  stop  battery 
charging  to  prevent  battery  damage  caused  by 
over-charging. 

Battery 
Overheating 

The controller  can detect the battery temperature through 
an  external  temperature  sensor.  The  controller  stops 
working when its temperature exceeds 65 °C and restart to 
work when its temperature is below 55 °C.

 

Controller 
Overheating

 

The controller is able to detect the temperature inside the 
battery. The controller stops working when its temperature 
exceeds 85 °C and restart to work when its temperature is 
below 75 °C. 

TVS High 
Voltage 
Transients

 

The  internal  circuitry  of  the  controller  is  designed  with 
Transient  Voltage  Suppressors  (TVS)  which  can  only 
protect against high-voltage surge pulses with less energy. 
If  the  controller  is  to  be  used  in  an  area  with  frequent 
lightning  strikes,  it  is  recommended  to  install  an  external 
surge arrester. 

 

 

Содержание GM3024N





















Отзывы: