background image

REV. 10/2019

2

G

Settings

When repairing or replacing hydraulic, electric or electronic components or assemblies, 

always note the truck specific settings.

Servicing and inspection

Thorough and expert servicing is one of the most important requirements for the safe 

operation of the industrial truck. Failure to perform regular servicing can lead to truck failure 

and poses a potential hazard to personnel and equipment.

The service intervals stated are based on single shift operation under normal operating 

conditions. They must be reduced accordingly if the truck is to be used in conditions of 

extreme dust, temperature fluctuations or multiple shifts.

The following maintenance checklist states the tasks and intervals after which they should be 

carried out. Maintenance intervals are defined as:

W = Every 50 service hours, at least weekly

A = Every 250 operating hours

B = Every 500 operating hours, or at least annually

C = Every 2000 operating hours, or at least annually

W service can be performed by the customer.

In the run-in period - after approx. 100 service hours - or after repair work, the owner must 

check the wheel nuts/bolts and re-tighten if necessary.

1.3

Содержание EPL153

















































Отзывы: