EOS P 396 Скачать руководство пользователя страница 110

Страница: 110 / 170

Data preparation

6.26

Training manual • Basic training • Status 03.14

EOS P 396

•

Repair surfaces or lines using

Magics RP

and slice repaired files again.

☞

section

6, Preparing parts with Magics RP

Automatically repairing parts

•

If only parts of layers are left or layers have been completely removed, these

layers can be replaced with the layer before or the layer after.

If surfaces of more than 1 mm² or lengths of similar size have been removed,

it is imperative the related layers are replaced.

•

Consider repair effort.

If necessary, replace part with an error-free part and prepare again.

☞

section

6, Preparing parts with Magics RP

☞

section

6, Preparing parts using EOS RP-Tools

Risk of data loss!
The extension

*_c.sli

appended during the

SLIFIX

correction run is not a

defined code for the

Automatic parameters

function in the

PSW.

On loading the data the

Automatic parameters

function therefore allocates

the exposure type No_Exposure to data corrected using

SLIFIX

Parts with the exposure type No_Exposure are not built.
Check in the

PSW

the exposure types for the parts.

Содержание P 396











































































































































































Результаты поиска

Содержание P 396

Отзывы:

Бренды по названию

Популярные бренды

EOS P 396, Руководство по обучению

Результаты поиска

Содержание P 396

Отзывы:

Бренды по названию

Популярные бренды